Embedded Motion Control 2018 Group 4

Group members

TU/e Number	Name	E-mail
1032743	Shuyang (S.) An	s.an@student.tue.nl
0890579	Leontine (L.I.M.) Aarnoudse	l.i.m.aarnoudse@student.tue.nl
0892629	Sander (A.J.M.) Arts	a.j.m.arts@student.tue.nl
1286560	Pranjal (P.) Biswas	p.biswas@student.tue.nl
0774811	Koen (K.J.A.) Scheres	k.j.a.scheres@student.tue.nl
0859466	Erik (M.E.W.) Vos De Wael	m.e.w.vos.de.wael@student.tue.nl

Files

File:EMC Group4 Initial Design.pdf

File:EMC Group4 Final Design Presentation.pdf

Initial Design

Goal

The main goal of the project is to enable PICO to autonomously map a given room and subsequently determine and execute a trajectory to leave this room. For the initial Escape Room Competition, the predefined task is completed once the finish line at the end of the corridor is crossed. For the Hospital Room Competition, the goal is to map all rooms situated in the complex, after which the robot returns to a given position from where it must be able to identify a placed object in order to position itself next to it. However, both competitions include several constraints:

• The robot must complete the task without bumping into any walls.
• The individual tasks must be completed within five minutes.
• The robot should not stand still for more than 30 seconds during the execution of each of the tasks.

Plan

Escape Room Competition

1. Initially, PICO should make a 360° turn once, to gather information about the surrounding environment.

2. It should act accordingly depending upon the initial data that is gathered. The following three scenarios are possible:

• A wall is detected, then it should go to the nearest wall and start following it.
• A door is detected, then it should go to the door, cross the finish line and stop.
• Nothing is found, then it should move forward until it detects either a wall or a door.

3. While following a wall, the following two scenarios are possible:

• Another wall is detected, then it should start following the next wall.
• A door is found, then it should go through the door and cross the finish line.

Hospital Competition

1. Initially, PICO should make a 360° turn once, to gather information on the surrounding environment.

2. It should start following the wall along the corridor, until a new door is found.

3. Then, it should enter the room through the new identified door, and start following the walls of the room. While following the walls of the room, it should identify all the corners of the room from the data gathered, and then exit the room. Also, while performing this task it is possible that a new door is detected inside the room, then it should enter that room and follow the same protocol as mentioned before.

4. Once PICO is in the corridor again, it should start searching for new doors, and explore each of the room similarly as mentioned above.

5. While performing these tasks, PICO simultaneously needs to create a map of the whole hospital. Once the whole hospital is mapped, it should park backwards to the wall behind the starting position.

6. After that depending on the hint given, PICO should find the object in the hospital and stop moving close to it.

Requirements

In order to follow the plan and reach the goal that was defined earlier, the system should meet certain requirements. From these requirements, the functions can be determined. The requirements are given by:

• The software should be easy to set-up and upload to the PICO.
• The software should not get stuck in deadlock or in an infinite loop.
• PICO should be able to run calculations autonomously.
• PICO should be able to make decisions based on these calculations.
• Walls, corners as well as doors should be detectable. This means that the data provided by the sensors must be read and interpreted to differentiate between these items.
• Based on the sensor data, a world model should be constructed. Hence, this model should store information that functions can refer to.
• PICO should be able to plan a path based on the strategy and autonomous decision-making.
• PICO should be able to follow a determined path closely
• PICO should be able to drive in a forward, backward, left and right motion.
• PICO should be able to turn with a predefined number of degrees (-90°, 90°, 180° and 360°).
• PICO should also be able to turn with a variable angle.
• The speed of each of the wheels should be monitored.
• The total velocity and direction of PICO should be monitored.
• The distance moved in any direction by PICO should be monitored.
• Detect when and for how long PICO is standing still.
• PICO should be able to either drive the entire rear wheel across the finish line or to stop moving close to the designated object for respective competition types.

Functions

In the table below, the different type of functions are listed. A distinction is made between the difficulty of the function, i.e. low-level, mid-level and high-level functions. In addition a distinction is made between functions that depend on input for the robot and functions that determine the output.

	Low-level	Mid-level	High-level
Input	Read sensor data	Detect wall Detect obstables Detect corners Detect doors	Area mapping Determine strategy
Output	Move forward/backward Move left/right Rotate Stop	Avoid collision	Positioning in front of doors Positioning for parking

Components and specifications

The hardware of the PICO robot can be classified into four categories, which can be seen in the table below.

Component	Specifications
Platform	Type: PICO, a telepresence type Jazz robot produced by Alderbaran Dimensions: H:100.5cm, W:41cm, D:35cm Weight: 8kg Max translational speed: 0.5m/s Max rotational speed: 1.2rad/s
Sensors	Laser Range Finder (LRF) Measurable range: 0.01m - 10m Measurable angle: 4rad Angle increment: 0.004rad Wheel encoders (Odometry)
Actuator	Omni-wheels
Controller	Intel i7

The escape room competition features the following environment specifications:

• PICO starts at a random position inside a rectangular room, which features one corridor leading to an exit.
• The corridor is oriented perpendicular to the wall and ranges in width from 0:5 to 1:5 meters.
• The finish line is located more than 3 down the corridor.

Most notably, the differences between the escape room competition and the hospital room competition include:

• PICO will start in the hallway of the hospital.
• The hospital features three to six separate rooms.

Interfaces

The interfaces for the initial design and the information exchanged between each interface are depicted in Figure 1. This figure shows how the code will be constructed, with separate functions that receive a certain input and give a certain output. For example, the planning interface will receive the current map, position and orientation. Based on that, it will decide on a target. That target will be used by the controller to determine the actuator input. What is not depicted clearly in this figure is the division between the world model and the registry. The world model contains information regarding the location of the corners and doors in the room. However, info like the current LRF data and the actuator input are not part of the world model. These are stored in the registry.

Figure 1: Initial design interface

Escape Room Competition

Our aim was to implement our own wall detection algorithm during the escape room challenge. However, due to time constraints we were not able to implement that in time. Therefore, we chose to use a potential field algorithm in combination with a wall follower instead. These algorithms were not yet tuned, and as a result did not perform as expected during the challenge. PICO followed the first wall, but bumped into the second wall while turning. Therefore, he could not complete the challenge.

After the challenge, several decisions were made. Because of the difficulties with implementing our own wall recognition algorithm, we decided to use the proven method of Split-And-Merge instead. Also, we decided not to use the potential field algorithm and wall follower for any further steps, since these were only a last-minute attempt at finishing the challenge. In the GIFs underneath, the split-and-merge algorithm is applied to the escape room challenge in simulation. The door is recognized fast, and the robot moves to a setpoint in from of the door. Using this algorithm with appropriate tuning on the actual robot, we believe that the challenge could be completed.

Final Design

For the final design, we are still working based on the interfaces used for the initial design. The plan that was mentioned before has been updated based on new information, and consists of the following steps. These are explained further in the section on the planning and discrete control.

Approach for the Hospital Competition

1. PICO will be oriented facing the corridor. Initially, it should scan what's in front of it and see whether a door is visible.

2. If a door is found initially, PICO should position itself before the door. Otherwise, it should start following the wall along the corridor, until a new door is found and position itself in front of it again.

3. Then, it should enter the room through the new identified door, and stop one meter into the room. Then it should scan, turn 180 degrees and scan again. It will determine all the corners of the room from the data gathered, and then exit the room. The information about the room, e.g. the location of the door and the corners, will be saved in the world model. While performing this task it is possible that a new door is detected inside the room, then it should enter that room and follow the same protocol as mentioned before. Information regarding whether a door has been entered before will be saved in the world model.

4. Once PICO is in the corridor again, it should start searching for new doors, and explore each of the room similarly as mentioned above.

5. While performing these tasks, PICO simultaneously needs to create a map of the whole hospital. Once the whole hospital is mapped and the end of the corridor is reached, it should park backwards to the wall behind the starting position.

6. For the second part of the challenge, PICO should determine what room requires the most doors to reach (which is the high level hint). This information can be found based on the information in the world model.

7. Then, the consecutive door locations are used as setpoints for PICO to follow towards the right room.

8. When the room is reached, PICO will scan it's surroundings and try to find a series of data points deviating from the know location of the walls. This will indicate the location of the object, so that a setpoint can be generated.

9. PICO will move to the setpoint next to the object and stand still, stating that he has found the object.

World Model and Registry

The center of the interface figure that was shown before is actually divided into two parts: the world map and the registry. The registry contains all current data, for example the position and orientation of PICO, the sensor data, a filtered version of the sensor data, the actuator inputs and the current target and setpoints. This is all relevant information that should be accessible for the functions, but should not be part of the actual world model.

The world model itself consists of different classes that each have their own properties. There are rooms and corridors, which are numbered and contain a collection of doors and corners. The doors have a state (used and unused), coordinates and a destination. The corners have coordinates as well. Using the coordinates of the doors and corners, the lines that form the walls of each of the rooms can be mapped. This information can then be used to determine the location of the object in the final challenge. Since the destination of each of the doors is known, it is possible to determine which room needs the most doors to reach and thus use the high-level hint. The known coordinates of the doors can then be used to generate setpoints to actually reach that room.

Discrete Control - Planning

For the hospital challenge, discrete (state) control will be required. Therefore, the following two state machines have been designed for the two parts of the challenge: mapping the hospital and finding the object. The first state machine works based on 'open' and 'closed' doors. Any door that is found that has not been entered yet, is saved as an 'open' door. When Pico starts this challenge in the hallway, he will scan what is in front of him. This might show an open door, if so, Pico will enter the room through this door. If Pico cannot identify an open door, he will drive one meter further into the hallway and scan again. When Pico has entered a room, he will assign a number to this room and save the coordinates of the corners and doors of the room in the world model. The door through which he has entered will be closed, and he will check the room for open doors. If an open door is found, Pico will enter the next room through this door and repeat the proces. If not, Pico will return through the closed door and eventually get back to the hallway to continue his journey through the hospital.

When the entire hospital has been mapped and Pico has stated that he is parked in the correct spot, the next state machine will start running. The principle of open and closed doors will now be applied to rooms. Pico will open the room that needs the most doors to reach, and go towards that room. When he has reached the room, he will scan it and check if there is an object , which will present itself as a series of points closer to Pico than the wall that would be expected at that sensor angle. If no object is found, the closest room that has not been opened yet will be opened and Pico will continue his search there. When the object is found, Pico will stand next to it and tell us all that he has accomplished his task.

Figure 2: State machine: mapping hospital

Figure 3: State machine: finding object

Continuous Control

Wall Collision Avoidance

In order to perform high level tasks and to make PICO move to set point generated by the discrete controller, a low level continuous control is required. The job of the low level controller is to mainly reach the desired set point as accurately as possible, while avoiding collision with walls. Therefore, the wall collision avoidance algorithm is integrated with the low level controller. The low level controller is a simple proportional controller, with 2 different gains for the x (P_x) and y (P_y) axis.

The wall avoidance algorithm is based on data from the laser range finder. The beam of the laser range finder is categorized into 3 sections: left, top, and right. In each section the data from laser range finder is checked whether there is an obstacle(wall) nearby, by setting a minimum threshold on the data from laser range finder. If at any instant, PICO detects a data point less than the given threshold, it marks the section containing that data point as closed space, and tells the controller that it cant move any further on that side. This is done by setting the proportional gain of the controller to 0 for that side, until PICO identifies that there is enough space to move towards that side again, which might happen when PICO sees a door on the same side where there is a wall. The width of each section of the beam is tuned to 30°, as it is observed that for very large beam width, PICO cannot identify door as a open space if the width of door is too small. Also, the minimum threshold is kept to 40 cm to prevent any collisions with walls or any other obstacles. The gif shows PICO moving to a set point while avoiding collision with walls.

PICO moving to a set point while avoiding collision with walls.

This idea of continuous control and wall collision avoidance is motivated by the way our predecessor (Group 4 of Embedded Motion Control 2017) implemented their space recognition algorithm.

Perception

The perception part of the interface will receive filtered LRF data and odometry data, so that it can determine the position and orientation of PICO based on that data. The LRF data has been averaged over several scans, outliers have been removed and one out of every five data points is selected, resulting in 'filtered' LRF data. The odometry data is assumed to be inaccurate, since the omniwheels of PICO tend to slip often. Therefore a way is found to improve the position estimation using the LRF data as well.

Using the split and merge algorithm in the monitoring part of the interface, markers are defined. These markers are the corner points found by the algorithm. Once PICO is in a room and has made an initial scan, the location of the corner points is known and it can be used to improve the estimation of new positions of PICO in that same room. The split and merge algorithm is slower than the odometry updates, but it can still be run within 5ms. Therefore, it can be used regularly to improve the odometry data. The difference between the previous and current positions based on odometry is compared to the difference in the location of PICO relative to the markers. These two position estimates are then averaged, and since the LRF data is assumed to be more accurate this is weighted more.

One disadvantage of this approach is that it is required to have markers defined in a room, before the odometry data can be improved. Therefore everything will be relative to the odometry-based position estimation that is made when the room is first entered. This leaves room for errors. It is assumed that for the monitoring and mapping, the perception will be accurate enough to get a rough mapping of the location of the corners and doors. This will be enough to generate setpoints and paths, and to recognize the object in the final part of the challenge. Also, the control will include an algorithm that monitors the distance to the wall and prevents PICO from driving into a wall.

Monitoring

Primary Feature Detection: Find gap

For escape room challenge, we use a primary feature detection strategy to find the gap within a scanning. This is also part of the advanced feature detection. After a scanning, the distance between every two neighboring points is calculated. If it's larger than the threshold, we could say it's two line segments. The number of segments could only be either one, or more than one. If PICO faces a closed room it could only find one segment, otherwise we just use the last point of first segment and the first point of last segment as feature points, take average and use it as the set point for controller. As shown if the following figure, the middle white point is always in the middle of the corridor.

Facing closed room - one continuous segment

Advanced Feature Detection: Split and Merge

The split and merge algorithm is used to identify and locate corners and doors based on the data provided by the perception interface. Based on the identified corner- and entry points, the hospital can be be divided into rooms. The split and merge algorithm is implemented in the following way:

1. Preprocessing the data (input: laser range finder, odometry, bias)

• Remove points that are not of interest: for each individual scan the LRF-data is limited to a scope of 180 degrees.
• Convert the LRF-datapoints from polar coordinates to Cartesian coordinates, make modification according to the bias-factor resulting from the localization.
• Use push_back() to store both the processed LRF- and odometry data into a vector.

2. Merge multiple scans (optional)

• Merge possible overlapping parts from multiple scans, in order to avoid duplicates.

3. Identify linesegments (input: processed LRF-data)

• Determine if the distance between two consecutive laser points is larger than the set threshold.
  • If true, store the indices A and B of these two laser points in a vector. The first and final laser point are also used as endpoint of a segment.
• Output: the initial- and endpoint indices of each segment after removing duplicates.

4. Identify corners

• For each linesegment fit the line crossing through the initial point as well as the end point, characterized by the equation:

[math]\displaystyle{ ax+by+c=0\; }[/math] [math]\displaystyle{ a=\frac{y_{1}-y_{2}}{x_{1}-x_{2}}; \qquad b=-1;\qquad c=\frac{x_{1}y_{2}-x_{2}y_{1}}{x_{1}-x_{2}} }[/math]

• calculate the shortest distance from this fitted line to each datapoint within the section using:

[math]\displaystyle{ \delta=\left|\frac{ax_{0}+by_{0}+c}{\sqrt{a^2+b^2}}\right| }[/math]

• find the datapoint with the largest distance to the fitted line, and check if the distance is smaller than the wall threshold.
  • if true, declare it's a wall between two points, go to the next step;
  • if false, declare it's a corner, replace the initial point with the found corner, go back to step 1 in this function and write down the max distance points index.
• connect two points that are declared as wall
• connect each corner point with increasing index within current section
• connect current sections initial point with the minimal index corner point, and connect the maximum index corner point with the end point
• output: a 2D vector, every contains all the feature point within that section

5. convert from index to point structure

• extract index from input, assign their corresponding coordinates and type flag to point structure
• distinguish three type of feature point:
  • the temporary point, or intermediate point
  • the corner of room
  • the point of exit

6. Merge map (update world model)

• push_back() new feature point to vector with point structure

Test Result

Static : These are some results of the implementation of the split and merge algorithm in simulation. On the left, the simulation environment is visible. On the right, the corner points that are found can be seen, as well as the lines that are fitted through these points.

Dynamic : The working of the split and merge algorithm is illustrated further in the simulation gifs that can be found below. Since the corresponding simulator gif is too large to play fluently, it can be found using this link: http://cstwiki.wtb.tue.nl/images/Split-Merge-Simulator.gif

Advanced process There are several tricks with the split and merge algorithm which are explained below. With these improvements the algorithm is more robust and it can extract more information.

Prevent missing feature point:
This happens when a corner point that has a large index, far away from the inital point, is detected first. Then the initial point is updated with the found feature point, and the possible feature point with a smaller index that's closer to the initial point is missed.
In order to solve this, a found feature point will not only be connected to the end point. Instead, two lines will always be connected from the last found feature point to its neighbouring features or endpoints. Then, it can be checked if there is a wall in between or if there are any other feature points in these fitted lines.
The figure below shows a simple scenario, in which the first line is created with the initial point and the end point of that section. Then the first feature point is found, because it has the largest distance to the line. This point is then connected with the initial point and the end point, creating lines two and three. In line three, one more feature point is found. Therefore line four and five are connected to the existing point. This process is continued until all lines are verified as a wall.

How to connect lines

Evaluate the quality of the detected feature:
In order to evaluate the quality of a detected feature, it is possible to check the size of a continuous section, i.e. the number of point in each section. If it's less than a certain threshold, we remove that section because its point density is too low. In the program we tune the threshold between three to six, and this gives kind of a trade-off between the possibility of missing a feature and improving the poor mapping quality.

Remove small section of scanning

Distinguish different type of feature points:
With the basic split & merge algorithm, the feature points and the end point of laser beam could be found. To distinguish these points within a section, first the number of feature points, i.e. the size of section, is checked. If the size is two, then all of them should be intermediate points. If it contains more than two points, then we should calculate the distance from PICO to the feature point and its neighbouring points as well. There is a preset variable to determine which point before and after the feature point should be used for distance calculation.
From one side to the feature point and the other side, if the distance goes down and goes up, it should be a exit point, while if the distance goes up and goes down, it should be a room corner.

Type of feature point

Only feature within current space:
During every scanning, the section of split & merge that's outside of the current space is not of interest, and may even cause confusion when updating the map. To overcome this drawback it's ideal to just keep the section within current space. This could be divided into two cases, the scanning in the corridor and in the room. Both cases use a boundary as a constraint to filter the data.

• Scanning in corridor: the boundary could be seen as the y coordinates of the wall. Initially PICO scans and gets the y coordinates of the -90 deg laser beam and of the 90 deg one. After that, every time that PICO scans in corridor, it should just check two conditions to see if a whole section's y coordinates are outside of the boundary, and if the distance from the boundary to the found section is larger than a threshold. Whenever these two conditions are satisfied, this section is erased from the vector.

Remove section of no interest

• Scanning in room: this is more complex than the case in the corridor, as there is no fixed boundary. If PICO faces a closed room, i.e. there are three walls without a door around PICO, all the sections that are detected would be within in this room. If PICO faces a wall with an open space, it may detect two exit points of the door, or even more between the door. This could be divided into:
  • Two exit points - remove all sections between the certain two sections that have exit point, as they are not of our interest
  • More than two exit points - remove all sections between the first and the last section that has an exit point, because only these two exit points are part of the door of current space

Remove section of no interest

Define a door: Ideally, a door is defined by two exit points. In reality this does not happen every time, either due to a door not being in the middle of the wall, or because the scanning doesn't cover the whole open space, so that only one or even none of the exit points is found during a scanning. The procedure of finding a door could be divided into two scenarios.
1. Find door from corridor

• From previous advanced feature detection, PICO may find some exit point from corridor, as the blue points shown in figure below. If the y coordinate of exit point is positive (left hand side), we assume the first point of next section is another exit point, as the red point shown in figure. If the distance between this hypothetical point and the exit point satisfies the 0.5-1 meter condition and their y coordinates difference is within a threshold, we define this is a door.
  
• Similarly, if the found exit point has a negative y coordinate (right hand side), we assume the last point of previous section is another exit point, and do the same check. Based on this method, PICO could find as much door as possible even with limited scanning data.

2. Find door from room
PICO enters a room, makes first scan, turns back and scans again. Since the door could be in the middle of a wall or at a corner, this could also be divided into three scenarios.

• Find two or more exit points
  

If the door is at the middle of a wall, PICO may find at least two exit points. Based on the advanced feature detection mentioned before, we could distinguish which section no belongs to current space. Thus a door could be easily defined by the first exit point and the last exit point, as shown below.

• Find one exit point
  

If the door is at a corner of the room, or is not facing directly to PICO, it may find only one exit point, as the blue point shown below. In this scenario, we check if there is corner of room as the neighbor point of the exit point. if there is, as the red point shown, we extend the line from corner of room to exit point and find the intersection with the rest part of the room, as the white point shown. Then the intersection point and the exit point could define a door.

• Find no exit point
  

The worst case comes when there is a door, but PICO may not find any exit point at first scan. In this case, if the segment number is larger than one, it indicates there should be a gap. Then the problem could be converted and solved by the primary feature detection mentioned before. PICO could use the found middle point of open space as the set point, drive there and scan once more.

Limitations

1. Wrong corner point
From simulations with different room setting, it is observed that split and merge works fine when PICO is not positioned straight in front of a wall. However, if PICO's x-direction is perpendicular to the wall, it's easy to find the wrong corner. This is caused by the method that is used to calculate the distance of points within a certain section to the initial end-line, which is explained in step 4 above. When the wall is (nearly) parallel to PICO's y-axis, there might be several points with a similar maximum distance, and one of these points could happen to be a non-existing corner, which is indicated by the red point in the figure below.

Possible solution:

• Since the laser range is 0-270 deg, use 0-180 deg and 90-270 deg to detect feature, double check and avoid the parallel scenario.
• When a corner is found, check its neighbouring points. If they could form a right angle, then it's concluded this is exactly the corner point.
• When a wall parallel to PICO's y-direction is detected, rotate over a small angle and scan once more.

Figure x

Figure x

Mapping results

The figure below shows some mapping results using split & merge in the simulator. <mention that the perception is not included>

Hospital Competition

Due to the limitation of time and incomplete components of interfaces, we finally only used monitoring and continuous control interfaces to compete in the hospital challenge. While integrating the monitoring and control interface several problems were faced because of which a complete integration could not be done before the challenge. Few problems that were encountered are as follows:

1. The continuous controller was designed to make PICO reach given a set point with no walls in between current position of PICO and set point, while avoiding any collision with walls. This was done because it was planned that discrete controller will set the way points, while monitoring will only map the environment and store all the important coordinates. Since that was not possible, monitoring was itself used to give out the set points to the continuous controller by evaluating the midpoint of the door, which at times can lead to set points with wall between PICO and the set point..
2. The scenario of turning PICO when an opening is found was not considered while designing the continuous controller, as we did not foresee this situation. Thus, PICO always moves sideways, forward and backward w.r.t. to the absolute frame of reference, which can lead to collision with wall when PICO is moving backwards given a setpoint, as no LRF data is available in that case.
3. Also, we experienced that the code was not able to make PICO move after first set point was reached. Although we tried to debug the problem, but we were not able to exactly resolve it before the challenge.
4. Without perception part, the precision of re-localization is not good enough. The monitoring uses an argument bias to make correction of the coordinates of the found feature, which has to be set to zero in reality. In simulation it works fine with only odometer data but on real robot, the error is larger than the threshold used in monitoring function, and the same feature point could not be relocated well. Also, continuous control highly depends on accurate odometry data, which is a very big limitation while implementing the controller on PICO without good odometry data.
5. Incomplete integration of monitoring into the world model causes the detected feature points only be stored in the format defined by monitoring part. It's okay to plot map but not easy for other components to use, especially store the states of PICO and use the high level hint.

Therefore, in the end our code was capable to identify all the feature points of the map, but because of unsuccessful integration with the continuous control, PICO could only move to the first door that was identified by monitoring.

Although all things did not go as expected, few things really worked out well. The monitoring algorithm correctly identified the first door and the set point. Also, the controller could track the set point well without any collision with the walls. Had the controller been properly integrated with monitoring, it would have been possible to map the full hospital. Also, with the availability of all the required interfaces and with proper interfacing the challenge could have been completed.

Interesting code snippets

For monitoring part, we mainly use split & merge algorithm, and together with some advanced feature detection methods mentioned above, such as distinguish different type of feature point and use door-definition to specify where is the door of current space.
<need more text why we are proud of these>

Conclusions and Discussion

Unfortunately PICO was not able to complete the set challenge inside the hospital with the implemented code. Though PICO was able to identify the first door and position itself in the initial room in order to scan the inside, the code malfunctioned once the robot had to turn around and continue to the next room.

Despite the fact that the code did not enable PICO to complete the mapping of the hospital, there are certain aspects to our code that we are particularly proud of. For instance, the decision to create a registry separate of the world model provided the opportunity for interfaces to be developed independent of each other. All interfaces can store and request varying data regarding position, orientation, sensor data and setpoints from the registry. Independent of the registry, classes such as rooms, doors and corners are stored. Also, the split and merge algorithm implemented in the monitoring interface proved to work quite well in scanning and identifying the different structural aspects of the hospital.

< Most notably the control and perception interface could have been improved>

In hindsight, it turns out that the general structure describing the interaction between the world model and the other interfaces should have been implemented in C++ in an earlier stage. Even though the main architecture was well defined conceptually, writing the corresponding code was postponed to a later stage. This in turn led to a lack of time to finish other aspects of the code at the end of the project. Had this general architecture been defined earlier on, then different parts of the required code could be divided among the group members who can work on it individually, while still ensuring compatibility with the other segments of code. Moreover, one significant pitfall was to think that we have to create all code from scratch. The limited time frame of this course forces you to be able to implement existing pieces of code and adapt it to meet your own requirements.

Recommendations

Based on the work done during the course, several valuable insights and recommendation for future work are stated:

• First of all, start learning to write code in C++ as soon as possible. Having a proper understanding of the structure, language and implementation saves a lot of precious time during the debugging phase.
• In order to enhance productivity, different aspects of the code must be divided among the group members. However, this implies that the main architecture of the different interfaces and their respective interactions should already be constructed in C++. This way it is clear what is required from each assigned task in terms of the input it needs and the output it provides to the others. Group members can work on their assignment separately, while still ensuring that the written code is compatible with the work of others.
• Due to the limited time and testing capacity available during the course, the main focus of the design should be to implement an as plain and simple code as possible; there is simply not enough time to create an extensive, complicated piece of code for the PICO robot.
• Likewise, already existing libraries, packages and algorithms should be implemented as much as possible in order to create the entire code needed in an efficient manner. Writing and debugging a new version of code for a certain task that has already been covered by others is just a waste of time.
• In addition, the simulator provides a useful tool to try and debug new pieces of code. Since actual testing time with PICO is limited, all tests should be prepared thoroughly in the simulator in order to efficiently use test time. However, it should be taken into consideration that the provided simulator does not account for all different aspects of the motion behavior of PICO. Hence, all simulated code should be verified by means of real-life testing.
• The escape room competition should be viewed as an intermediate opportunity to test the working of the code up untill that point: it is not a goal in itself. Focusing solely on escaping the room can result in having to start from scratch when coding for the hospital competition. Rather write the code in such a structure that it can be used in later stages of the hospital competition as well.