Firefly Eindhoven - Localization - Top Camera
The top camera is mounted above the soccer field of the Drone lab and provides a nearly full view of the soccer field. In the Firefly project it is used for localization of drones and ground robots using LED markers on these devices. We have developed software to capture images from the camera, process them and to track moving targets equipped with markers. Compared to the Ultra-wideband and ultrasound technologies a high refresh rate of around 17 FPS is possible, but the detection is less precise and quite unreliable due to reflections and LEDs blocked by the net spanning the soccer field. Further development of the detection algorithm may remedy these deficiencies to some extent.
Hardware
The camera is manufactured by Allied Vision (exact model unknown) and can capture images and live video at 20-30 FPS in Full HD resolution (1920x1080). It is an industrial camera and can be connected to a laptop using the Ethernet cable labeled "Laptop" (ethernet connected cameras are typically referred to as GigE cameras, named after the interface). Allied vision provides the Vimba Software Development Kit (SDK) to interface with the camera in software, you will need to install this before you can use the tracking application.
Software procedure
Extension to multidrone procedure
From I to L shape
To get from the I shape to the L shape, the geometry of the code had to be changed. It was decided to create vectors between the three points, and to find the direction between the two vectors. This was done by rotating the first vector 90 degrees clockwise and taking the dot product between the rotated vector and the second vector.
This uniquely determines which of the two vectors is part of the front of the drone, because if the angle is negative (meaning turned less than 180 degrees counter clockwise with respect to the previous vector), this means that the second vector could be made by rotating the first one counter clockwise, meaning that the second vector is the vector between the two LEDs at the front of the drone. If the angle is positive, the second vector could be made by rotating the first one clockwise, and therefore the first vector is the vector between the two LEDs at the front of the drone.
Bearing this in mind, the angle of the drone can be determined by creating a vector perpendicular to the vector between the points in the front and exactly in the middle of those two points. The angle of the drone will be the angle between an arbitrary vector that is pointing into the phi is zero direction and the vector just explained. The x and y position of the drone can be easily calculated by taking the average between the two outer points.
Getting from one to multiple drones
To get the camera to detect multiple drones, a distinction had to be made between LEDs of one drone and another. To do this, a K-means algorithm was used to find
[math]\displaystyle{ ceil(\frac{\#_{LEDs}}{3}) }[/math]
clusters, where [math]\displaystyle{ \#_{LEDs} }[/math] is equal to the amount of LEDs the algorithm has found. This means that the algorithm would find clusters equal to the amount of LEDs it found divided by three, rounded up. This was done to make sure the K-means algorithm would prefer to make groups of three LEDs, which is the amount of LEDs on a drone.
These clusters of LEDs were analyzed to see if they had more or less than three points, or if these points were too close together or too far away to be a drone. If any of these conditions were true, the cluster is deleted from the list. If no clusters are left after this procedure, the exposure of the camera would be changed to find more or less LEDs. The clusters of three LEDs would then be given an ID based on the previous positions of the drones, if available. If the program finds an extra drone or it is the first frame, the IDs are given in the order the K-means gives the results, which can be seen as random.
Design decisions
During the design, certain decisions had to be made in terms of robustness and accuracy. These decisions are summarized next. The first design decision that had to be made was which points to use to calculate the angle. Using two points will be less accurate than using three points, but taking the third point into account will decrease the robustness as checking if this point is on the right line to validate the results afterwards will not make sense if this point is also used in the calculations. It was decided to go with the two points and using the third point as a check because if the point was too far off to be of use, the check after the K-means would already have gotten rid of the drone and the robustness was valuated as more important than the accuracy due to this. The second design decision that had to be made was when to throw away results and when to keep them after the K-means. This is because a four LED result could still be a drone but a fourth LED could have appeared due to reflections. Checking these results would make sure that more drone results will be displayed and the frequency that a drone would not be detected for a single frame would decrease, but the computation time would take longer and if the algorithm would be wrong and would detect a drone without there being one, the drone which it detected wrongly would think it would be at a completely different position and therefore would suddenly give a high thrust in an unexpected direction, potentially ruining the show. Therefore the robustness of the program would decrease greatly if not implemented correctly. For this reason, it was decided not to implement this.