RoboShark
Project by Twan Haazen
Supervisor Rob Janssen
This wiki will contain information about my Bachelor Final Project.
Introduction
Lorem ipsum dolor sit amet, consectetur adipiscing elit. Sed vestibulum convallis justo, at vulputate risus vulputate et. Fusce non velit vitae quam dapibus ullamcorper. Lorem ipsum dolor sit amet, consectetur adipiscing elit. Integer tincidunt rhoncus massa, ac fermentum risus sollicitudin vitae. Nulla vitae orci sit amet erat feugiat malesuada a a leo. Vestibulum sem ligula, aliquet eu blandit eget, gravida vel eros. Maecenas pharetra congue massa at sodales. Aenean condimentum, tellus id sagittis malesuada, nibh nunc feugiat orci, dictum consectetur lacus neque sit amet sapien. Class aptent taciti sociosqu ad litora torquent per conubia nostra, per inceptos himenaeos. Morbi adipiscing arcu ullamcorper purus commodo ac elementum augue hendrerit. Pellentesque volutpat enim sed tortor consequat in iaculis ante pharetra. Cras tristique semper urna, id bibendum sapien lobortis id. Donec nisi eros, mattis sed fermentum sit amet, accumsan a libero. Sed sapien mauris, varius a placerat eget, ultricies at ligula. Mauris dignissim ornare pulvinar. Nulla facilisi. Cras nec interdum est. Integer quis accumsan sapien. Quisque vehicula, metus id accumsan fringilla, mauris mauris adipiscing nisi, eget molestie velit mi et lorem. Maecenas augue massa, pulvinar sed adipiscing at, posuere eget dolor. Nam ligula odio, ultricies sit amet mollis sit amet, gravida at erat. Donec pellentesque, nisl at rutrum posuere, nibh urna tincidunt turpis, imperdiet gravida massa nisl nec nunc. Ut in felis ut quam posuere mattis. Nam quis tortor quis arcu scelerisque tincidunt. Vivamus non euismod purus.
Pre-Design Research
Brainstorm Sessions
After the decision was made to base the design on a shark, the actual brainstorm sessions began. The most important parts of the these brainstorm session will be discussed here.
The first thing that came to mind, was to search for as much information as possible about projects that did about the same as I was planning to do. When discussing the assignment, the german company Festo had some interesting video's and projects about helium filled balloons. Festo developed the Air Penguin as well as the Air Ray. The Air Penguin is an autonomously flying penguin that communicates with other penguins in the air. The Air Penguin makes sure it does not hit any walls or obstacles and does this by using ultrasound to pinpoint its location. The Air Ray is a remote controlled helium filled balloon which simulates the flying mechanism of a manta ray. Both these projects are closely related to the product I would like to produce. By exploring the website of Festo and contacting the people that worked on these projects, I tried to get as much information as possible to get a clear vision on how to design my shark.
One of the first things that can be concluded from of both of these projects is that the construction has to be very light. The Air Penguin, with a length of 4 meters and a maximum diameter of 80 centimeters, had a total weight of only 1 kg. This requires well use of construction material and space.
After studying the designs of Festo, the first sketches of the prototype are drawn. The first idea consisted of a large balloon filled with helium. Onto this large sack the several components of the shark are attached. The tail section is made out of several thin rods which will be moved in horizontal direction by a servo. This part will function as the propulsion of the shark. With the side fins the shark can turn and move up and down. The fins can be rotated and the tips can be moved op and down to make steering possible. The first sketch is shown in figure (X)
The second sketch the design has changed. To make the structure more rigid and define the shape better a frame is added. The tail section will also consist of a frame section instead of only 4 single rods as in the previous design. The propulsion is still the same, with the tail section move in horizontal direction using a servo. The side fins are the same as the ones in the first sketch. The second sketch is shown in figure (X). There is a problem with this sketch, the weight of the total frame construction might be to heavy for the helium filled balloon to keep the shark neutrally buoyant.
Using the ideas of the brainstorms sessions, the several parts of the shark can now be designed using both paper as well as a 3D CAD-design. But first needs to be determined how much weights helium can lift.
Helium
The shark will float through the air by using helium. To determine how much helium is needed to make the shark neutrally buoyant Archimedes’ principle is used. This principle states that any object, wholly or partially immersed in a fluid, is buoyed up by a force equal to the weight of the fluid displaced by the object. In the following section a relationship between the mass of the shark and the volume of the balloon needed is derived. Following Archimedes' principle, the upward lift is defined in equation (1).
The whole shark will have a certain weight on which a gravitational force is applied. The total amount of gravitational force is given in equation (2).
To make the shark neutrally buoyant the force from the upward lift has to be equal to the force applied by gravity, which is displayed in equation (3). If the upward lift equals the gravitational force, no net force in vertical direction will be present.
Substituting the terms from equation (1) and (2) in to equation (3), a relation between the mass of the shark and the amount of helium needed can be derived. This relation is given in equation (5)
[math]\displaystyle{ \rho_{air} \cdot g \cdot V = (M_{shark} + \rho_{helium} \cdot V) \cdot g \qquad (4) }[/math]
If the assumption is made that the temperature is equal to 293K and the pressure is 1 bar, the density of air is equal to 1,204 kg per cubic meter. At the same conditions the density of helium is 0,1787 kg per cubic meter. Using these values for the densities of air and helium, 1 cubic meter of helium can make 1 kg neutrally buoyant. Using equation (5), the size of the balloon needed to make the shark neutrally buoyant can be determined.
Design
Tale Section Design
The first thing that was designed was the tale section of the shark. This part is responsible for the propulsion of the fish. According to the movement of a shark, this part will translate in horizontal direction. To make this translating movement a flexible rod will have to be used. The start of it will be connected to the main part of the shark and at the end a large part of foam will be attached to provide the proper amount of area to ensure the propulsion. Surrounding the flexible rod some in between part will be attached to form the shape of the shark tale. A thin line of fish wire will go through these parts and will be connected to end of the tale. If pulled on one of these ends, the flexible rod will deform in such a way that it will bend in the direction of the side where the force is applied. If afterwards the force is applied on the other side of the tale, the flexible rod will bend the other way. With this bending back and forth, the desired translation of the tale is acquired. A small but strong servomotor will provide the proper amount of force to bend this rod. Below a sketch of this design is shown from the top. Also a 3d CAD-design is shown.
image
Prototypes
Tail Section Prototype
After the designing phase, a prototype has been build. The flexible rod is a part of flexible plastic and the in between parts are made out of MDF. Small holes have been drilled into these parts to allow the fish wire to run through it. When applying force into these wires the tale of the shark bends as required. This is shown in the figures below.