Hexapod

Installation

The installation assumes that Ubuntu 12.04 LTS is installed. If not you should install an Ubuntu version. Notice that the version of Ubuntu determines line 3 in the following code i.e. precise.

# Setup your computer to accept software from ROS.org
# 12.04 (precise)
sudo sh -c 'echo "deb http://packages.ros.org/ros/ubuntu precise main" > /etc/apt/sources.list.d/ros-latest.list'

# Set up your keys
wget http://packages.ros.org/ros.key -O - | sudo apt-key add -

# Installation
sudo apt-get update
sudo apt-get install ros-fuerte-desktop-full
sudo apt-get install ros-fuerte-orocos-toolchain
sudo apt-get install ros-fuerte-rtt-common-msgs

# Create your personal ros directory
mkdir ~/ros_personal

echo "source /opt/ros/fuerte/setup.bash" >> ~/.bashrc
echo "export ROS_PACKAGE_PATH=/opt/ros/fuerte/stacks:~/ros_personal" >> ~/.bashrc
echo "export RTT_COMPONENT_PATH=/opt/ros/fuerte/stacks/orocos_toolchain/install/lib/orocos" >> ~/.bashrc
echo "source /opt/ros/fuerte/stacks/orocos_toolchain/env.sh" >> ~/.bashrc
. ~/.bashrc

# Build SOEM
cd ~/ros_personal
git clone http://git.mech.kuleuven.be/robotics/soem.git
cd soem
git checkout origin/electric
rosmake soem

# Build hexapod
cd ~/ros_personal
svn checkout http://hexapod.wtb.tue.nl/svn/hexapod ./hexapod
roscd hexapod
rosrun rtt_rosnode create_rtt_msgs hexapod_msgs
rosmake

# You still should get
## (1) pr2_spring_transmission_example
## (2) orocos_components_dev

It is possible to put the code in a shell-file and run it.

SVN

The code can be found on: http://hexapod.wtb.tue.nl/svn/hexapod/.

To obtain an account you should contact Patrick van Brakel. To keep the svn clean i.e. no build, bin or lib files do the following:

sudo gedit /etc/subversion/config 

Uncomment, by removing the '#' and add

global-ignores = *.o *.lo *.la *.al .libs *.so *.so.[0-9]* *.a *.pyc *.pyo
  *.rej *~ #*# .#* .*.swp .DS_Store lib build bin .tb_history msg_gen srv_gen

Hardware

The TU/e hexapod is a six legged robot with compliant joints. The compiance is obtained by using torsional springs between the actuators and the joints. The motors as well as the joints have absolute encoders. From the difference between these readings, the torsion in the springs can be calculated.

There are three main PCBs on the robot. The PCB inside the bottom of the robot (data aquisition module or DAM1) communicates with a computer. This can be the on board computer or an external pc. It is also equipped with an IMU that can measure pitch and roll angles, roll rates about three axes and accelleration along three axes. Furthermore, it receives power directly from the battery or external power supply and feeds it to the other boards.

The PCB on top of the robot (DAM 2) translates the signals it receives from a controller to electric currents for the actuators. The middle PCB is the on board computer on which it is possible to run the robot's software.

Software

The software on the SVN contains, among other things, a Gazebo model and control programs that communicate with the hardware through SOEM-drivers. There are several launch files that should start the necessary programs.

Many files inside the hexapod_launch/deploy_files folder contain hard coded paths. Make sure to substitute them with the actual one.

The 'SOEM_hexapod_drivers' package contains a launch file named 'start.launch'. This runs the basic interface of the hexapod robot. From the Soem process, it is possible to, for instance, read the encoder signals or write commands to the actuators, using the Slave1001 service.

OROCOS components

Hexapod Encoder

This is the encoder component. It reads a message coming from the encoder port on the Soem board and outputs three different messages: a status, necessary for the actuators to be enabled, and a joint and actuator reading.

Hexapod Actuator

This is the actuator component. It reads two messages at his input ports: the command message, that can be either 0 or 1, enables the actuators. The control message is what the motor is receiving and it's written to the output port of the component, connected with the Soem board.

Hexapod Safety

This is the safety block that handles the limits in the joints revolution such that motors and cables are not damaged. It enables/disables the motors according to that.

Start up

Hardware

To power the hardware, there is a 24V connection on the bottom of the robot. There is a possibility to connect one of the LiPo battery packs or alternatively to wire the robot to a laboratory power supply. When connecting a power supply, make sure the current is not limited too much (you need more than 3A, 10 should be enough). Once this is connected, the robot can be booted using the small button that is connected to two loose wires.

Troubleshooting

• The Soem master could not initialize on eth1

1. Make sure that you are connected to eth1 or otherwise change it in the *.ops file.

To list the network ID's form your PC use the following command in the terminal:

ifconfig

• If the setcap cannot be found.

install the setcap

sudo apt-get install libcap2-bin

• If the followin error occurs:

[ ERROR ][Soem] Could not initialize master on eth1.

Set the permission for the deployer-gnulinux such that it can use ethernet.

roscd ocl
cd bin
sudo setcap cap_net_raw+ep ./deployer-gnulinux