Embedded Motion Control 2019 Group 5

Welcome to the Wiki Page for Group 5 in the Embedded Motion Control Course (4SC020) 2019. This page contains the design plans and other details of our work in this course.

Introduction

Group members

Name	TU/e Number
Winston Mendonca	1369237
Muliang Du	1279874
Yi Qin	1328441
Shubham Ghatge	1316982
Robert Rompelberg	0905720
Mayukh Samanta	1327720

Introduction

The world around us is changing rapidly. The new technological possibilities triggers new ways of life. These innovations, like self driving cars, could make life easier but also safer. In this course we have programmed a robot to assist in the hospital, instead of a self driving car. However, autonomous robots in a hospital environment could decrease the amount of mistakes in a hospital. If the robot is programmed correctly, it could deliver the right medicines to the right patient. Also, since a robot never sleeps, patients could get their medicine at night, if they need something for the pain for example. In our challenge we had program a robot (PICO) which is able to drive to different cabinets (hence patients), recognize the different cabinets and recognize it has arrived (hence delivering the medicine.)

Overview of Wiki

The wiki will cover the main topics regarding our project. Several functions which are crucial for the program are discussed in detail. Furthermore the challenges are described in detail, the strategy applied is covered, the results are covered and also some thoughts for improvements are given.

Task Requirements

In the following section the task requirements of the PICO are given.

Generic

The following performance requirements are expected to be met for the:

1. PICO should be able to leave the room from any initial position.
2. PICO should not hit the wall of the room, the corridor or (dynamic/static) objects under any condition.
3. PICO should not remain idle for more 30 seconds.
4. PICO should be able to move translational with a speed of 0.5 m/s and rotational with a speed of 1.2 rad/s.
5. Only one executable has to be called in order to start.

Escape Room Challenge

The following performance requirements are expected to be met for the Escape room challenge:

1. The rear wheels of PICO have to pass the finish line
2. PICO should complete the task within 5 minutes.

Hospital Challenge

The following performance requirements are expected to be met for the hospital challenge:

1. PICO should determine its position with respect to its surroundings (walls, obstacles, etc.)
2. PICO should determine its position on the global map in the world model.
3. When PICO visits a cabinet, it should give a clear sound of which cabinet it is visiting (i.e.,“I have visited the cabinet zero”).
4. PICO has to make a snapshot of the map once a cabinet is reached.
5. PICO should reach all the cabinets in a correct order.
6. PICO should be able to detect the obstacles.
7. PICO should not hit any walls and objects except for slightly touching.
8. PICO should try to detect the static and dynamic objects and present them in its own world model.
9. PICO should complete the task within 10 minutes.

Hardware Description

PICO has several components which are:

• Sensors:

1. Proximity measurement with Laser Range Finder (LRF)
2. Motion measurement with Wheel encoders (Odometer)
3. Control Effort Sensor

• Actuators:

1. Holonomic Base - Omni wheels that facilitate 2D translation and rotation

• Computer:

1. Intel i7 Processor
2. OS: Ubuntu 16.04

• Interaction

1. PICO has the ability to produce sound through a speaker in its body
2. PICO has a display, mounted on top of the robot

Software Architecture

World Model

File:World model.jpg
The world model contains the data’s generated by the LRF and odometer along with various other variables which are computed within the system and later used by different function block. There are two types of data which are stored in our World Model.

1. Environmental Data
2. Robot Data

Environmental Data

• LRF data
• Global Map in the form of Binary Map.
• Corners
• Cabinets
• Exits
• Cabinet Que

Robot Data

• Robot State
• Robot Position
• Desired Trajectory
• Odometer
• Robot Position
• Robot Offset

Measurement

Data	Description
Scan (LRF Data)	It gets the data from Laser range finder and sends the information to World model which is used later for by measurement function to get BMI information from measurement function.
Odom	it gives the data about the rotation done by PICO which is stored in world model and sent to the measurement function.
Basic Measurement Information (BMI)	These are the various other information such as the maximum and minimum distances as well as the distance of objects at left, right and center of PICO as well as the angular orientation of Pico with respect to the map.

Mapping

Data	Description
Scan	It gets the data from Laser range finder and sends the information to World model which is used later for by mapping function to generate local Binary grid map.
Corners	Scan data is used by mapping function to generate a list of corner points which are essentially the concave points in the map and is used later used for getting the position of Pico within the map.
Exits	these are the convex corner points which are detected as the exit points at a certain room which is used to get out of the room.
Localize	this function within the Mapping uses the scan data to create grid map by converting the polar data to Cartesian coordinates and transform that to a local grid map which is used to update the global map and calculate the robot offset.
Global Map	the JSON file is used to convert the points to a Global grid map.

Planning

Data	Description
Trajectory	Based on the robot position information and cabinet list provided by world model the planning module generates the set of the trajectory which is sent to the world model.
updated cabinets	The planning module sends back the updated cabinets’ queue list to the world model.

Actuation

Data	Description
desired trajectory	The desired trajectory data is sent to Actuation which computes the desired X,Y velocity to follow the required trajectory

Functions

Measurement

The laser range finder present on the PICO is used. This data is received in an array, where the indices contribute to some angle and the value of the second column present the distance to the nearest point in that direction. For calculating the angle range of the PICO is determined during the configuration state. Once this is done, the total angle is divided by the angle increment of the PICO to determine the length of the array and multiplied again to know the angle. From the angle and the radial distance, a set of Cartesian coordinates can be calculated which are used in the localization and planning parts.

In the function part named 'measurement', different return values are designed to determine states of reading the data received by PICO, including laser data and odometry data. Then, the middle interval of the whole scanning range of PICO is defined as its front center index and the direction of the interval pointed by 90°/-90° with respect to the front center index is defined as left/right index. The farthest distance and the nearest distance which could be detected are recorded and updated in the model 'getMaxMinDist'. In addition, environment states (existing obstacles or not) of three directions (front, left and right direction of PICO) are also processed and updated in this model. In the model 'sectorClear', four return values are defined to express different states faced by PICO directly which show the distance between PICO and obstacles. The next model in measurement is 'alignedToWall', compare the distance ***. Moreover, angle increment, maximal angle and minimal angle are also recorded in this function.

Additional Functions

The main functions are aided by some other necessary functions which are as follows:

1. Data logging: The function helps to store the LRF data during the simulation process which could be used to understand how PICO sees the area around itself.
2. Polar to cartesian conversion: The raw LRF data is in polar form. This function is converts the LRF readings to cartesian coordiantes for creating a grid with a specific resolution.
3. Json to Binary map: The function is used to create a binary map with walls represented as one's and empty region as zeros.
4. Padding walls: Since the Astar algorithm algorithm tries to find the shortest possible path, there are chances that it could create a path brushing the walls. This would result PICO getting too close to the wall which is undesired. This function makes a wighted padding with the walls getting the highest weights.
5. Astar: This function computes a path from the current position of PICO to the goal point which are positioned near each cabinet.
6. Distance calculation: The function calculates the distance between any two points in the grid map.

Escape Room Challenge

Link to Challenge Description

The detailed description for the Escape Room Competition could be found here.

Challenge Strategy

Initial stage in the strategy is to scan the room and search for the exit. If the exit is not found PICO will continue to rotate until it manages to find an exit. If still the exit is not detected then PICO will move approximately to the center of the room and rescan the room for an exit. This case was put in when it was observed during test runs that PICO does not manage to identify the exit if the initial position was parallel to the wall containing the exit Once the exit is found Pico will move towards the center of the exit. As soon as the exit is reached, adjustments so PICO orients the corridor. Once that is done, PICO will start to follow the corridor until it detects no corridors around itself.

End Result and Future Improvements

In the first attempt PICO slightly bumped into the wall while entering the corridor due to oscillatory movement and high velocity during diagonal movement. In the second round the maximum transnational velocity was reduced which helped it to enter the corridor smoothly. The challenge was completed in 40 seconds. Eventually our group managed to win the completion and we got some beers at the end of the final competition for the same!

Hospital Challenge

Hospital Competition is the second part of the course Embedded Motion Control. In this competition, PICO could determine the cabinet in each room and face towards all the cabinets in the right region marked previously for the given start area. When PICO visits a cabinet, it should give a clear sound of which cabinet it is visiting (i.e., “I have visited the cabinet zero”) and reach all the cabinets with a correct order. PICO could detect the obstacles in this competition not only static objects but also dynamic ones (Such as the walking actor in the hallway) and not hit any walls and objects except for slightly touching. PICO should also try to detect the static and dynamic objects and present them in its own world model. Finally, PICO should complete the task within 10 minutes and must not remain idle for more than 30 seconds. This is a brief presentation slide with a basic introduction of Hospital Competition, which could be found here

Link to Challenge Description

The detailed description for the Hospital Competition could be found here.

Initial Design of Escape Room Competition

A brief summary of embedded software functions design is described in the following chapters.

Design Document

The Initial Design Plan for the Escape Room Competition and the Hospital Competition with PICO could be found here.

Functions

	Function	Description
High-level	Detect Wall	Set a safe distance between wall and PICO. If there are too closer with each other, PICO would execute corresponding movements.
	Detect Corner	Detect the number of corners of the room.
	Startup	Identity the initial angle of PICO in the start position. And then, compute an angle -- θ.
	Scan for Exit	Rotate PICO to detect all the distances between wall and robot in order to find the exact position of the corridor.
	Move to Max	If PICO do not detect enough walls in the room, it will move to the direction of the maximal distance and detect walls again.
	Face Exit	Let PICO face to the exit corridor straightly but not perfectly. PICO would not rotate itself in a defined error range.
	Drive to Exit	PICO moves to the exit.
	Enter Exit Corridor	Enter the exit corridor with a safe range between the walls of the corridor and PICO itself.
	Follow Corridor	Follow the walls of the corridor with a safe range until PICO crosses the finish line.
Low-level	Initialize	Initialize actuators
	Read Data of Sensors	Read the odometer and laser data
	Drive Forward	Move straightly
	Drive Backward	Move back
	Drive Left	Move left
	Drive Right	Move right
	Turn Left	Turn 90°left
	Turn Right	Turn 90°right
	Turn Around	Rotate
	Stop Movement	Stop current movement.

Escape Room Challenge Execution

• Introductions about functions of code. Explain each mode more or less in order to let readers know what happened in our PICO. Just like what Winston did in Tuesday evening. -- YI

Startup

This mode involves computing the required angle for PICO to complete a full 360 degree view if needed. Once the angle has been determined the state switches to SCAN_FOR_EXIT.

Scan for exit

This mode searches for an exit in its available field of view which is around 230 degrees. If it does not manage to find an exit in this field of view, it uses the angle computed in the STARTUP to complete to rotate until it manages to find the exit. If it happens to be the case that it still did not manage to find any exit it switches to a state MOVE_TO_MAX. This scenario is generally encountered if PICO is initially put in a corner adjacent to the exit wall.

Hospital Competition

The main objective for PICO is to "deliver" the medicines from one cabinet to another which will be defined by the judges just before the challenge starts. The PICO will be operating under an environment amidst static and dynamic obstacles.

here

Software architecture

The main components of our architecture are the world model, the planning, the mapping, the measurement and actuation parts. The world model contains all the data of the environment and data like the position of the robot. The mapping module ensures the world model is updated and a map is provided. The planning ensures a path is planned from the current position of the robot towards a certain goal. The measurement part feeds data and some basic information into the word model and the actuation ensures the robot actually moves. These components will be worked out in more detail below.

World model

The world model contains all the data of the environment and the robot like its position. From the world model information is sent towards the other blocks, which process them and provide new information to the world map.

Measurement

For the measurements the laser range finder present on the PICO is used. This data is received in an array, where the indices contribute to some angle and the value of the second column present the distance to the nearest point in that direction. For calculating the angle the range of the PICO is determined during the configuration state. Once this is done, the total angle is divided by the angle increment of the PICO to determine the length of the array and multiplied again to know the angle. From the angle and the radial distance a set of Cartesian coordinates can be calculated which are used in the localization and planning parts.

Planning

To be able to plan a path the A* algorithm is used.

Mapping

we create two types of map
1.Global map.
2.Local Map

Global Map

In order to implement the A* path planning algorithm, the given map, which is in the form of a json file, is converted into a binary map. The objects of the map is given based on points with x and y coordinates. The walls and cabinets are described with lines, where the lines are defined by the start point and end point.
The first step to build the binary map is to find the range of the map. Therefore,

This is created using the Json file , which contains the x,y coordinates of the points which make up the wall and cabinates.
Using the x,y coordinates of the points we create the binary map made up of 1's and 0's where 1's represent any sort of obstacle such as walls or cabinates.

Local Map

This is created from the laser data provided the LRF .
We convert the LRF data to cartesian cordinates which in turn is used to convert it to binary map made up of 1's and 0's.
This map is used to identify any sorts of unknown structure which can be added to the global map for path planning.

Results

Improvements

During the project the implementation ideas changed a lot. It is advisable to come to an agreement of the final implementation as soon as possible.