PRE2017 1 Groep3

Members of group 3
Karlijn van Rijen	0956798
Gijs Derks	0940505
Tjacco Koskamp	0905569
Luka Smeets	0934530
Jeroen Hagman	0917201

Introduction

The technology of robotics is an unavoidable rapidly evolving technology which could bring lots of improvements for the modern world as we know it nowadays. The challenge is however to invest in the kind of robotics that will make its investments worthwhile instead of investing in a research that will never be able to pay its investments back. In this report we are going to investigate into a robotics technology that we think is worthwhile looking into. In this chapter it will be explained what the societal issue is that we want to tackle, what we want to achieve for this issue and how we plan on achieving this.

Problem Definition

When you travel by train on a regular basis you might have noticed that when people in a wheelchair need to exit or entry the train it goes rather slow. Before they can get on or off the train the train personnel is needed first to get some sort of ramp to make the disabled people able to board or deboard the train. When someone in a wheelchair is on board or wants to go on board of the train the train might even be delayed because of this. As we know trains in the Netherlands tend to be too late every time and therefore every obstacle that is getting in the way of letting them ride on time, should be taken care of. The wheelchair problem is definetely one of them. Imagine you are in a wheelchair and want to board the train. First you have to look for someone of the staff to ask if they can help you board the train. Someone of the staff will then get the ramp and help you board the train when it has arrived. When you have reached your destination and you want to exit the train again someone of the staff at the trainstation has to get the ramp and help you deboard the train. As you can see it is a lot more difficult for people with a handicap to be able to easily travel by train. Every time they want to travel by train they are dependent of other people. The feeling of constantly being dependent on others is for most people the worst part of living with a handicap. Because of this dependency the threshold for these people to travel by train is much higher. When they stop using the train it might have an impact on their social being which might cause loneliness and even depression. We as group 3 want to improve the service at trainstations for disabled people by using the technology of robotics.

Objective

As already mentioned in the problem definition it is our goal to improve the assistance for disabled people at train stations. In order to achieve this goal we need to specify what is actually meant by improve. To see what the best eventual goal would be the wishes of the users need to be considered. The primary users are of course the disabled people, however the indirect user, which is the train staff, also has their own wishes. To be able to know what the users want their opinion is needed, which will be discussed under the USE chapter. Here our view of the ideal solution will be explained. As explained before the dependency on others is one of the main problems and therefore it would be best if everyone could board the train all by their self without the help of any staff. Another problem was the time it takes to board the train and therefore we want a solution that is as fast as possible but of course also entirely safe to use. Another important part are the manufacturing costs, which of course are preferred to be low. Also the product should be easy to use and not wear off too quickly since reparation costs will be high on a robotic system.

Approach

The approach for the project will be discussed in this section. First of all the users wishes should be the main design criteria. To find out what the wishes of the users are there 2 questionnaires will be made, one for the disabled people and one for the train staff. The results of these questionnaires will be used for a thematic analysis. From the conceptual designs the one that fits the wishes of the users best and is the best solution according to the other design criteria will be chosen. After the best conceptual design is chosen a literature research will be executed about the options of the design. When the literature research is completed a prototype will be designed which will represent the final solution of the project. With the prototype it can be seen what things of the design should be adapted to improve the design.

To make sure that the project will be finished in time milestones have been made which show what we want to finish in every week from now on. The list of milestones can be seen in the planning.

Project planning Gantt chart

User and enterprise analysis

To get a better view of the design criteria the design should comply to, the user aspect of the problem statement and the objective will be considered in this section. Moreover, the topic will be discussed from the perspective of several other stakeholders, such as society and and train companies(i.e. the Nederlandse Spoorwegen)

Who are the users?

The first step is determining who the users are. The main users are, of course, disabled people who travel by train and will actually use the robot. This project will focus on the user by means of a questionnaire. To avoid a technology-push, it is very important to get a thorough view on the user's perspective on the current situation, and the needs of the user. This questionnaire focuses on the way they are helped right now and what the advantages/disadvantages of the current state are. Also their initial feeling with being helped by a robot in the future is an important part and in what way they would prefer to be helped. Questions like those are incorporated in the questionnaire.

What is the NS' perspective?

The NS is a very important stakeholder in this project, for they are the ones that will eventually need to pay for the research and manufacturing of the robot. Moreover, the NS staff is also the current user; in the current situation, they help the disabled people board the train by means of a ramp. It is therefore very important to get a better view of what the operating NS staff thinks of our idea. For this purpose, another questionnaire is made.In this questionnaire the view of the train personnel is asked regarding the current assistance and what they think that could/should be improved. Also their view on the idea of a robot helping the disabled people is important.

The questionnaires

Summarizing the above, there are multiple reasons for which the questionnaires are designed:

• To gain insight into the current situation with regard to traveling by train when being disabled. How does the current system work? How do people experience the current system?

• In order to finetune our RPC’s for the robot, the aim is to gain insight in the wants and needs of the actual users: NS staff and disabled people. What do they believe is necessary in order for the system to work efficiently? What do they miss in the current situation?

• To improve the system for all its users, not necessarily only disabled people. Therefore we are also curious to know how operating NS staff experiences the system? What can be improved for them to improve their work efficiency and pleasure?

To find participants for this study, several steps were taken: a call on Facebook was posted for the target groups, personal networks were contacted and NS staff on the stations was approached. The questionnaires could be filled in online, or on paper. We aimed to get 5 participants for the disabled target group, and 2 to 3 for the NS staff. These amounts are based on what is reasonable for the scope of this project; due to time constraints it is not an option to find large groups of participants. The questionnaires were written in Dutch.

The questionnaire for the disabled

In this section all aspects of the designed questionnaire will be discussed. The questionnaire was designed to get insight into several aspects of the project:

The first two questions explore the current situation:

1. How often do you travel by train?

2. How much time does it take you to plan your train journey?

After this, several questions test the subjective experience of the current situation.

3. How do you experience the current NS travel assistance service?

4. What do you think could be improved in the current situation?

5. Are you capable of getting on to the ramp without help?

6. Do you experience difficulties in planning your train journey with regard to the NS travel assistance service?

7. How much time do you generally need when changing trains?

8. How do you experience travelling by train from 1 to 10, with 1 not pleasant and 10 very pleasant

9. Can you clarify your answer for question 8?

After this set of questions, the new concept is introduced and tested:

10. For this project, we aim to develop an automated system that functions as a ramp. By pressing a button on the platform, the robot will drive towards the train entrance and fold out to form a ramp. What would you think, of being aided with entering the train by a robot or automated system?

11. What are important aspect of good service for you?

12. What type of help with boarding the train would you appreciate most? (For example: ramp, lift, etc.)

In the final question we leave space for the participant to write down remarks or tips:

13. Do you have any tips or remarks with regard to the current or new system?

The questionnaire for NS staff

This questionnaire focuses more on the specific experience of NS staff working with the system and how it could be improved in their view.

The first questions explore the current situation:

1. What is your specific function at the NS?

2. How often do you help disabled people boarding or leaving the train? (1x per week, 1x per month, 1x per year, etc.)

3. In what way do you help disabled people boarding and leaving the train?

The next set of questions explores the subjective experience with the current system.

4. What are the advantages of the current system?

5. What are the disadvantages of the current system?

6. How would you rate the system with regard to NS travel assistance from 1 to 10, with 1 very negative and 10 very positive?

7. What could be improved in the current situation, to make your working experience more pleasant?

The next questions introduce the new concept.

8. For this project, we aim to develop an automated system that functions as a ramp. By pressing a button on the platform, the robot will drive towards the train entrance and fold out to form a ramp. What is your first reaction to a system like this?

9. How do you experience the current time needed to help a disabled person board or leave the train? Too long/too short?

The final question leave room for the participants to write down any thoughts on the topic:

10. Do you have any tips or remarks with regard to the current or new system?

Other stakeholders

It is important to consider all other stakeholders in this project while designing.

• Another aspect of the project are other train passengers, they should not be disadvantaged by the new wheelchair assistant. Therefore, it is undesirable that the new robotic assistant will cause any train delay. Moreover, it is important that there is still room for the other passengers to board and stay on the train. This should be considered to see if the new design has an impact on the other passengers.

• The government is also a stakeholder, as they are the institution responsible for making society as handi-friendly as possible. They may therefore be involved in partial funding of the project.

Thematic analysis of the results of the questionnaires

In the thematic analysis, we gather all codes from both questionnaires, and by combining the codes we will create themes.

Improvements

Combining codes from the questionnaires related to improvements for the current system yielded several improvements: first of all, one of the disabled wanted it to be possible to change trains faster. Moreover, accessibility of all stations as a disabled person is wanted. The staff wanted a better operability of the current bridge, and a better communication with the taxi company. In the current situation, NS travel assistance is only possible at the larger, manned stations. If a disabled person wants to travel to a smaller station, he has to contact an NS-connected taxi company. Those taxi drivers namely have access to the bridge, and are appointed to help disabled people get off of the train. Unfortunately, especially in case of disruptions in the train schedule, clear communication with the taxi company is lacking.

Staff

This theme encompasses the current situation fully; from the questionnaires we yielded the info that there are multiple parties involved: the disabled person, NS service staff, NS conductors, and, like mentioned above, appointed taxi companies. From the codes we have established the service staff escorts the disabled person on the bigger stations, taxi companies on the smaller stations, and conductors are mainly involved in maintaining safety at all times. The conductor mentioned helping a disabled person about 3 times a way, whereas the service staff helps over 20 times a day.

Advantages of current system

In this theme we can merge all codes related to advantages of the current system. Staff reported as advantages the following: the time needed for reporting is short, the time needed for helping is short, localization of the disabled person in the train is clearly communicated. A disabled person reported arriving on time at the desired station as an advantage.

Disadvantages of current system

The disabled people reported having little room in the train as a disadvantage. Staff reported the system is failing in case of train disruptions, and it takes too much time.

New concept

By aggregating all codes, in this theme we can take a look at the opinions on the new concept and important aspects of the system. Disabled people reacted positive, whereas NS was generally negative towards the concept. The staff made clear they thought they might be losing their job to the robot, and they considered it impossible for an automated system to work because of crowdedness. The disabled mentioned an extending shelf and lift as possible idea, and aspects that the system should have are: it should be fast, it should give the disabled influence on the situation and it should be suitable for different users with different disabilities. Of course, the above could be combined with the improvements for the current system.

Schematic overview

The above themes can be aggregated and examined to discover new relations between themes. The main result of the questionnaires is a better view on the current situation, and the identification of user requirements for the new concept.

Current situation

In the theme Staff we have established how exactly the current situation works. New information for us is the involvement of taxi companies.

User requirements

Multiple themes above can be used to identify user requirements. The new concept should namely build on the Advantages of the current system (it should in the least not remove those advantages), it should avoid the Disadvantages of the current system, it should incorporate the Improvements mentioned, and it should be aware of the aspects mentioned in New concept. If we combine this, we can make a list of all user requirements:

• The new concept should make changing trains as a disabled person faster

• The new concept should grant accessibility to all train stations and all platforms

• The operability of the new system should be good for staff

• The system should communicate with appointed taxi companies, depending on what their role is (in the ideal situation taxi drivers no longer need to operate the bridge)

• The new system should not have a longer reporting time than in the current situation

• The new system should not take longer in helping the disabled person than in the current situation

• It should be clear where in the train the disabled person is located

• The new system should have enough room for the disabled person to sit within the train

• The system should work at all times, also in case of train disruptions

• The system should work even in very crowded situations

• The new system should work as fast as possible

• The new system should grant the disabled person influence on the situation

• The system should be suitable to all types of disabled people with different disabilities

Process description

State of the art

In the following section you will be guided through the current process of boarding a train when you are disabled.

• First, you have to contact the NS to apply for NS travel assistance. This can be done in two ways: by telephone or online.
  • In case you want to do it online, you have to one-time register with NS, after which you should plan your trip. Then, you can ask for travel assistance.
  • By telephone you simply have to pass on your trip as planned, after which the NS can provide travel assistance.
• In both cases the disabled person has to contact the NS at least one hour before travelling. You cannot travel anywhere if you are disabled; travel assistance is only possible at about 100 of the 400 train stations in the Netherlands.

• After applying, you have to be at a pre-set meeting point at least 15 minutes before your train departs.
• The travel assistant will then take you to the right platform and help you enter the train.
• This happens as follows: the travel assistant, often with another NS employee, takes the ramp (which is on wheels) and rolls it towards the desirable train entrance.
• Then, they fold out the ramp and align it correctly with the train’s height. This happens after all other passengers have entered the train, ideally at a train entrance where there is plenty of room for the disabled person to stay during the trip.
• After docking the ramp, the disabled person either drives up the ramp himself or the NS travel assistant helps.
• As soon as the person is inside the train, the NS staff begins to fold up the ramp again and they bring it back to the original position on the platform.

• The NS then contacts other staff at the destination station and pass on in which train compartment the disabled person is.
• Then, at the destination station NS staff can take the ramp again and simply have to wait for the person to arrive.
• As soon as the train arrives, they help the person leave the train in a similar way as they help them with boarding.
• Often, the NS travel assistant helps the person during the entire process, which means he will only stop helping as soon as the person is off the platform and ready to continue its journey in the city of destination.

Idealized solution

The idealized solution has to fulfill every requirement, preference and constraint. The biggest goal is that disabled people are able to travel all by themselves. This means that they can reach the platform and use the automated assistance system to exit and enter the train without any staff being involved.

• When someone arrives at a train station the first thing they need to do is to get to the right platform with the use of the elevators that are already present at every station.
• A pole to check in with the OV-card will be located next to the elevator. The people that need assistance when entering or exiting the train have a special OV-card which can be used at the check in pole to activate the automated assistance. At the pole the user enters his/her desired destination.
• When the train arrives the robot will then locate itself at a door of the train.
• The person can then enter the robot which helps them enter the train.
• In the mean time, at the desired destination, the robot is stationed already at the door where the person wants to exit the train (this information is transmitted through the OV pole).
• When the person then arrives, he can leave the train immediately.
• During the movement of the robot the robot should always pick the shortest but also the safest path to the door. With safest is meant that the robot should never hit any obstacles or any passengers. To realize this the robot needs to be aware of its own position and the position of obstacles and people. This is a very important aspect, which will be elaborated on later in this wiki.
• The robot should therefore be able to constantly adapt its driving path to avoid moving obstacles as efficient as possible.

Conceptual Designs

In order to get to a right solution for our problemstatement conceptual designs need to be made. Five different conceptual designs where formed and on the basis of the RPC's and the analysis of the questionnaires, the best conceptual design will be chosen. To come to a preliminary design the best conceptual design is adapted to fullfill the requirements and preferences of the users even more. In this section the list of RPC's will be given together with five conceptual designs and at last the preliminary design.

Design 1

Design 1 involves an autonomous driving vehicle which can automatically drive to a certain location at the platform. The car only drives in a straight line parallel to the railway and therefore one robotic vehicle is needed per platform. The robot has wheels and an extendable shelf that can be attached to the train when the doors are opened. When someone wants to use the robot to board a train one simply walks up to the robot and pushes a button. The robot will be positioned at the end or front part of the platform depending on where the nearest elevator is located. When the train has arrived the robot will move to the door that is nearest to its location. This is either at the rear of the train or at the front (depending on which direction the train travels). The robot will be positioned using sensors in the doors to let it know where the doors are located exactly. When the doors are opened the robot will unfold its ramp and the person can board the training. By the use of a pressure sensor in the shelf the robot knows whether the person has entered the train. After the person has entered the train the robot will lift the shelf up again and then drives back to its original position. When the person inside the train wants to exit the train at a certain station the (not yet existing) extension of the NS app can be used. The app shares the information with the robot and the robot can know in advance that someone wants to exit the train. The robot can move in place when the train arrives (it can start moving when the door sensor is within its reach). When the doors open the shelf will be put in place again and the person can exit the train. When the person has left the shelf and is on the platform the robot will again lift the shelf and go back in its original position. To make sure the robot has enough power there will be a power station at the beginning position of the robot. The robot can attach to the power station and charge his batteries (same way as the lawnmower robot).

Design 2

Design 2 uses a crane to lift wheelchairs and moves them on or off the train. With this design there is no need for a car on the platform. There will be designated doors for people in wheelchairs where the crane positioned on the train. The crane has a lifting cable with four universal clamps which can be locked on the wheels of the wheelchair. The advantage of this concept is that it does not need anything on the platform which can cause obstructions for other persons. Getting off the train is just as easy as getting on. You will not have to worry if whether the crane is on the right platform at the right door and on the right time when you arrive, because the crane moves with you in the train. The disadvantage of this design is that you need to attach the clamps to the wheelchair yourself. It does not work autonomously. If you are incapable of operating it yourself, you still need someone to help you. The second disadvantage is that all the trains need to be adjusted, which takes a lot of time and will probably cost a lot of money.

Design 3

Design 3 is in many ways similar to the current ramp that is being used at NS stations. It involves two ramps that are folded upwards, and when one wants to use the ramp both sides flip down and level with the desirable height. At one side of the ramp this equals the height of the entrance of the train, and on the other side this equals the height of the platform. In this way, a person in a wheelchair can simply drive upward or downward if one wants to enter or respectively leave the train. When the ramp is folded upward, a simple user interface could be installed. The screen would allow interaction between user and platform; the user could enter an ‘order’ after which the robot can perform its duty. The robot is driven by two large wheels, one on each side, which allow for easy rotation within the platform environment. The robot autonomously navigates in this environment. The robot is stationed at one single spot per platform, where it can recharge itself after serving. The ramp has raised edges, to avoid someone falling off of the ramp.

Design 4

This design will focus on the docking problem for an autonomous robot. The wheelchair boarding system, as mentioned, has three main stages. The alert, dock and board stage. In this design the vehicle will use wireless network and latency to triangulate the position. There will be beacons in the platform, this could also be in the docking station, but that is probably less accurate. The robot has two sender/receiver combinations. One on the front and one on the back. They will send signals to the beacons, the beacons resend them. With the latency information the robot will be able to triangulate its position and orientation. At the same time there is a send/receive combination module under the stair of the train. This will also ping the beacons. The beacons then again triangulate the position and send this information to the robot. So at this moment the robot knows where it is and there is also a goal. In order to move to the goal, there are at least three things required:

Solutions

• The motion is to be planned within the kinematic constraints of the robot. A Quintic polynomial could be used to control start values of position, velocity and acceleration. The problem is that the robot is constrained in it's movement. So the orientation matters. We could describe the path as a series of robotic links, making constraints between the links. In a way the robot can always go from one to another.
• The motion should be tracked by suppressing disturbances. This could be done using the kinematic equations of motion represented in a state space.
• It has to move around obstacles, human and inhuman. This could be done by planning a path around it. Proximity sensors make a map of the nearest obstacles. Just a thought on this problems allows to fantasize a solution where the controller tracks the path, but starts deviating from the path as the sensors pick up obstacles. So instead of thriving for zero error, the error could increase with sensor input. The human obstacles are mobile, which means that they could move aside if urged to.

The solutions posed for the problems are made up using current knowledge. In order to find smart solutions, we might look into "Truck Docking". This is investigated by truck companies and shows a similar problem.

Design 5

Design 5 is an autonomous mobile lifting robot on four wheels that will help the disabled person board the train without any assistance from railway employees. The robot is stationed at a charging hub on each platform and has to be activated through the NS app and physical interaction with the OV-chipcard. Once the trip is planned and you "log in" on the robot with your chipcard, the robot will move itself to where the train will stop, ideally already aligned with a train door. Then, the train arrives and the robot will autonomously align itself with the door and open the back gate so the disabled can ride into the lifting platform. Then, the backdoor closes for safety and the person is lifted. When at the right height, the front door is brought down so the wheelchair can move over it into the train. When the person has left the robot, it should detect this and return to its original position and then move back to the charging hub as soon as possible so other passenger can use the door. This design will be connected to wifi to get the trip information from the NS app and accurate train arrival times. In order to be ready to dock to the train when it arrives, the disabled person has to activate the robot to move to the correct position 5-10 minutes before arrival of the train. It will have to avoid passengers and bags on the ground on its own, but ideally this problem is limited by either introducing a "wheelchair robot path" on the ground so people know where to avoid placing bags or it has sensors in front that enable it to manouvre around these objects. Because it has accurate trip information through the NS app the robot will know train arrivals in which a wheelchair is, so it needs to be ready to help this person get out of the train completely on its on, without any physical "log in" with the ns app.

Preliminary design

The Preliminary design is basically a combination of design 1 and ….. The design will be a autonomously driving vehicle that can be placed at each platform. The vehicle has 4 wheels and uses a horizontal plate that can be lifted up and down to be able to reach the right height to enter the train. It will only be able to drive in a straight line parallel to the train rails. It will be placed at one end of the platform which we will call its homing position. At his homing position a power station will be placed. The robot will always come back to the homing position and attach itself to the power station. The robot has to be equipped with different kind of sensor. For example the robot should be able to sense obstacles in its drive path. When the robot senses something is in its way it should stop and give some kind of signal to let it surroundings know that something is blocking the robot. Another design challenge is to find out how the robot can locate a door where the person can enter or exit the train. The first idea for a solution to this is to equip every train with a sensor at the very first and last door of the train these doors will then be used as an entrance for disabled people. An advantage of this solution is that the robot can always choose the door which is nearest to its homing position and therefore less people will walk in its driveway and the time to arrive at the door will be short.

Literature research

A modern wheelchair lift

Most railway companies in other European countries are bound by law to accomodate disabled people onto their train. Trains like the Eurostar have dedicated spaces inside trains in the 1st class cars, and allow for an additional passenger to come with the wheelchair bound customer. (source 2) Most railways companies work like the NS system, you have to plan your trip ahead of time (online or through customer service) so the railway employees can help you along your trip. However, not all trips are allowed because railway companies like Deutsche Bahn have a specific time that they need to make sure you can transfer between trains, thus some passengers have to wait for the next train because a 10 minute transfer between trains is not possible. (source 3)

Either ramps or mobile wheelchair lifts are used. These are stored on the platform and chained to a pole or wall and the railway employee will put this ramp in place for you. Then, when it’s connected to the train door the railway employee will push you on board or place you on the mobile wheelchair lift. When you are on the lift both sides are closed and the employee presses a button to align the height with the train door. Once it’s done lifting, the front ramp will go down and you can ride on the train on your own. It’s also possible for trains to have a ramp inside the train floor that goes out when a button is pressed. Companies that use the wheelchair lift are: VIA Canada, TGV (France), SBB (Switzerland), Trenitalia (Italy).

Starting in 2013, a test was done in Den Bosch with led lights on the platform to show where the train will stop and where doors are located, including which wagons are full and which are empty. The results of this experiment have been included in the NS app, which now shows how long trains are and how busy certain trains are. (bron 4)

RPC's

Requirements

• Completely safe to use for the disabled person but also completely safe to other passengers on the train.
• Able to use continuously, if not it will cause delay for the train or the person misses the train.
• Easy to use, disabled or elderly people have to be able to operate it.
• Completely autonomous, this means that the disabled person can enter and exit the train all by their self.
• The solution should not cause delay for other people who want to board the train.
• The solution should take care of faster boarding and deboarding than the current approach.
• The solution must be resistible to weather conditions and aging.

Preferences

• Let the person board and deboard as fast as possible.
• A solution that is as cheap as possible for both research costs and manufacturing costs.
• As comfortable as possible to user.

Constraints

• Solution has to fit for every different train, think about the width of the doors and the height of the entrance.
• Solution has to fit on the train station, possibly requires power and therefore needs some powersource.

RPC's compared with existing solutions

Requirements

• Completely safe to use for the disabled person but also completely safe to other passengers on the train.

This requirement is quaranteed for the current solution since train staff is involved it is completely safe to use.

• Able to use continuously, if not it will cause delay for the train or the person misses the train.

Since only one is available per platform it could cause delay when two trains arrive at the same time at the same platform. This requirement is therefore not applicable for the current solution.

• Easy to use, disabled or elderly people have to be able to operate it.

Currently the ramp is not operated by the disabled people but by the trainstaff, therefore it can not be compared.

• Completely autonomous, this means that the disabled person can enter and exit the train all by their self.

As said before the ramp is operated by the train staff and therefore the current solution does not apply with this requirement.

• The solution should not cause delay for other people who want to board the train.

The current solution is in most cases not causing delay for other people since they wait till everyone else has entered the train before the help the disabled person with entering the train.

Patent Check

There are no existing patents regarding the basic idea of autonomous train assistance. This patent check was done by inserting the terms wheelchair, train and wheelchair, lifting into the US Patent & Trademark Office search tool which includes international trademarks. Source 1

Safety regulations

Safety regulations for autonomous driving:

For autonomous driving vehicles there are up to today no universal laws or regulations. A congress[1] near the end of this year should shed some light on this issue. For now we think it suffices to make the vehicle as safe as possible, so the risk of getting in a hazard while driving is minimal. The people around the vehicle should be aware it is driving and have to move out of the way, this can be achieved with an alarm and floodlights.

Safety regulations for lifting people:

There are a lot of rules and regulations for lifting a person, but most of them are simple like: the lift should be designed to minimize the risk of getting in to a hazard. The full list of rules and regulations can be found here: [2.x]. The important thing we should take in mind regarding these safety regulations is that in no case the vehicle can flip over while lifting a person or the person can drive off the lift while going up or down.

[1]: http://www.autonomousregulationscongress.com/

[2.0]: http://www.hse.gov.uk/work-equipment-machinery/lift-persons.htm

[2.1]: http://www.hse.gov.uk/work-equipment-machinery/machinery-directive-essential-requirements.htm

[2.2]: http://www.legislation.gov.uk/uksi/2008/1597/schedule/2/part/1/made

Proof of concept

As can be read in the literature research part the idea to lift the a plate in order to enter the train is already used in some countries. However this principle is then used in the way the ramp is used in the Netherlands. The plate still has to be controlled by the train staff and therefore the disabled people can still not enter and exit a train all by their self. To be able to proof that our idea could work in real life a prototype is going to be build. Since it would be too extensive to build the entire robot the focus will be on determining how to reach a certain location. The lifting of the plate is already proven to work since it is already used. The last part of our idea that needs to be proven is how you can activate the robot and how to let it know which position it has to reach. This also applies when someone wants to exit the train, how does the robot locate the position of the person that wants to get off board? To solve these problems a literature research will be executed together with some brainstorming. To prove that the robot will actually be able to reach a certain position the prototype has some requirements, preferences and constraints.

What problem does the prototype solve?

Because the lifting system is already a proven concept in other countries, we will not try to prove this in our prototype. However, in these countries you still need to make reservations and need help from railways personnel. Thus, the thing our prototype will have to prove is that it is able to autonomously help the disabled customer. This means that from start of the trip to the end of the trip, no external help from railway personnel is needed. This starts with the planning of the trip; disabled people will be able to plan their trip in the NS app and "reserve" the robot to make sure it is available to them at a specific time. The NS app is linked to their OV-chipcard, so when the trip is planned, all the robot will have to do is scan the chipcard. Of course, this does not need to be an hour before departure and can be done when you arrive on the platform. The prototype will try to prove that no railway personnel is needed. This means that it needs to move autonomously from start to finish. When "activated" the prototype will move to the right position (closer to the edge of the platform, in front of where a train door will be). All moving that this protoype will do includes the avoidance of people and objects in its path. -korte uitleg van een zin hoe we objecten gaan waarnemen- In the real life, the disabled person in the wheelchair will have to follow the robot. Then, when the train has arrived, the prototype will move itself perfectly infront of the door. Because the boarding mechanism is already a proven concept, we exclude this from our prototype. When it is done, the prototype will return to its initial position and return to idle mode.

Our prototype will observe the world in front of him and will be able to discern between a moving object (person or moving bag) and a stationary object (a bag or person standing still). This will be done detail toevoegen hoe we dat uiteindelijk precies doen (met rode and blauwe blokken of niet, etc.). When the prototype observes a stationary object, it will wait a certain amount of time to make sure it is infact a stationary object. Then, when the object isnt moving, it can signal it by an alarm going off that it needs to move. When this does not happen it needs to move around the object. -toevoegen hoe we precies om objecten heen gaan in onze code-. Then, when the train arrives, the prototype needs to let persons out of the train first before continueing the boarding process.

Determining location of the door

For the robot to be able to help a person exit the train the location of the person in the train is needed. The trains in the Netherlands do not stop at exactly the same place on a platform every time. This will cause a problem when a robot is being used. In Den Bosch they are experimenting real time updated led lights to show the people were a door will be located when the train stops. This information can be useful for determining the location of the person on board of the train. When the location of the door for handicapped persons is known the system can send this information to the robot. Then the robot knows where someone is located and can drive to that location.

File:Ledlights.PNG

Role of disabled person in the solution

The solution could also let the disabled person play a role in it, for example that the vehicle is controlled by the person. When brainstorming about the concepts another approach could be to let the disabled person be the one who controls the vehicle/ ramp. This way the person can access the train without any help of the staff without the need of the vehicle being autonomous. One idea was to let the person board the vehicle at its homing position and then let the person control the vehicle with a joystick and in this way be able to place the vehicle in position their selves. The problem with this is however that the person that needs assistance is not always able to control the vehicle. Think about people that cannot use their arms or people suffering from blindness. Another option was to let the robot follow the person that needs assistance. This solution could be very useful when people want to enter the train however when someone wants to exit the train there is no one to control the robot. This problem is actually also true for the first idea. Because of this it is decided that the person will not be a part of the solution. The robot should be able to drive to the right location all by itself.

Unusual situations

As we all know the trains do not always function as they should do. To deal with delayed and canceled trains the robot needs to be aware of this. Imagine that the location of where the train arrives at a trainstation then the robot needs to be aware of this in order get to the right door. To solve these problems the NS app will be used, this app will send the real time updated information to the robot to let it know when trains are delayed or moved to a different platform. With this information the robot is always able to get to the right location in time. The people that need to use the robot can activate it with this same app in order to let the robot know when it has to drive to a certain location.

RPC's prototype

Requirements

• Drive in a straight line and be able to correct its movement.
• Drive by one press of a button to a desired location, robot needs to find the right location and be able to reach it.
• Avoid hitting obstacles, therefore the robot needs to be able to sense objects in its surrounding that are at least within 1 meter of its own position. When an obstacle is too close the robot has to stop and let its surroundings know that something is blocking its path.

Preferences

• Not only drive in a straight line but determine a path and be able to make turns.
• Reach the desired location as fast as possible, without risking to hit an obstacle.
• Be able to sense an object in its surrounding and in case the object is in his pathway be able to alter its path to navigate around it.
• The prototype should be as cheap as possible.

Constraints

• Drive alongside the railway without falling of the platform.
• The prototype cannot cost more than €150,-
• The prototype should have dimensions around 30X30 cm

Prototype research

Motion Planning

Literature

In order to plan a path for the mobile robot from station to the train door there is some investigation needed. We started looking for papers about trajectory planning for mobile robots with kinematic constraints. Therefore we started searching for some interesting articles on the topic. several search terms were used (path planning, kinematic constraints, mobile robot, real-time path evaluation). path planning with kinematic constraints real-time path evaluation mobile robot

1. Real-time randomized path planning for robot navigation
J Bruce, M Veloso - Intelligent Robots and Systems, 2002. IEEE …, 2002 - ieeexplore.ieee.org
... A higher value of this gain value (beta) results in shorter paths from the root to the leaves ... Several
important lessons can be drawn from this work in the context of real-time path planning: ... for the
extend operator may perform better than a more correct model when planning time is ...
Geciteerd door 482 Verwante artikelen 

2. Mobile robot trajectory planning with dynamic and kinematic constraints
V Munoz, A Ollero, M Prado… - Robotics and Automation, …, 1994 - ieeexplore.ieee.org
... planner, a local path planner, and a path tracker to execute the planned paths [9]. The ... paper
proposes a solution based on the combination of a simple local path planning algorithm, an ...
according to the kinematic and dynamic constraints of the vehicle and the path's features. ...
Geciteerd door 62 Verwante artikelen 

3. New potential functions for mobile robot path planning
SS Ge, YJ Cui - IEEE Transactions on robotics and automation, 2000 - ieeexplore.ieee.org
... X. Yun, and V. Kumar, “Control of mechanical systems with rolling constraints: Application to ... for
publication by Associate Editor J. Ponce and Editor V. Lumelsky upon evaluation of the ... To
overcome this problem, the repulsive potential functions for path planning are modified by ...
Geciteerd door 794 Verwante artikelen 

4. Guidelines in nonholonomic motion planning for mobile robots
JP Laumond, S Sekhavat, F Lamiraux - Robot motion planning and control, 1998 - Springer
... Guidelines in Nonhotonomic Motion Planning for Mobile Robots 15 in an iterated algorithm that
produces a path ending as close to the goal as wanted. ... These results are critical to evaluate the
combinatorial complexity of the approximation of holonomic paths by a sequence of ...
Geciteerd door 919 Verwante artikelen 

5. Dynamic path modification for car-like nonholonomic mobile robots
M Khatib, H Jaouni, R Chatila… - Robotics and …, 1997 - ieeexplore.ieee.org
... [3] BH Krogh and CE Thorpe. Integrated path plan- ning and dynamic steering control for
autonomous vehicles. In Proc. ... [8] S. Quinlan and 0. Khatib. Elastic bands: connect- ing path
planning and control. ... Optimal paths for a car that goes both forwards and backwards. ...
Geciteerd door 169 Verwante artikelen

So searching only gives us a lot more leads.... Christoph Spruk states in "Planning Motion Trajectories for Mobile Robots Using Splines" that "Motion planning for wheeled mobile robots (WMR) in controlled environments is considered a solved problem. Typical solutions are path planning on a 2D grid and reactive collision avoidance." While his thesis goes into higher levels of planning, it also equals 110 pages. In general we are feeling overwhelmed by information and the complexity of it. Furthermore, we are convinced that the most complex solution is generally not the best solution for us.

So instead of searching for "the answer" in literature we started using current knowledge to construct a basic solution. This way we can deliver intermediate solutions and enhance the solution where it is necessary. It also allows for more specific problem statements.

Solution

It is difficult to plan a path, without a world view, because the environment is continuously changing (e.g. walking people). In order to be able build and program a working intelligent prototype for this problem, advanced programming skills are needed. The framework to sense and construct a world view is beyond the scope of this project. To still achieve our goal, we used our basic knowledge of programming to construct a state based algorithm. The algorithms main objective is to reach its goal. When the robots sensors sense an obstacle, it switches state to avoid collision and maneuver around it. The code is shown below:

%This is a function that finds the goal using position and orientation
while pos ~= goal_pos % We want to loop until we reach the goal position
   % The first loop makes the robot move towards the goal as long as there
   % is no obstacle in it's way
   while S_F == Empty
       th_R = %ask angular position Robot
       th_G = %ask th_goal
       
       e = th_G - th_R
       T1 = -e*C1;
       T2 =  e*C1;
       
       if e <= pi/32
           T1 = T1 + C2
           T2 = T2 + C2
       end
   end
S_G = S_F % the sensor that is looking at the goal is the sensor on front
   % Then the robot turns until the front is clear and drives on until the
   % way towards the goal is clear.
   while S_G ~= empty 
       % update the sensor that looks towards the goal
       if dth =< pi/4 && dth > 7*pi/4
           S_G = S_F
       elseif dth =< 3*pi/4 && dth > pi/4
           S_G = S_L
       elseif dth =< 5*pi/4 && dth > 3*pi/4
           S_G = S_B   
       elseif dth =< 7*pi/4 && dth > 5*pi/4
           S_G = S_R
       end
       
       dth = 0
       th_R = %ask angular position robot 
       % Turn until the front of the robot has clearance
       if S_F ~= empty
           dth = dth - pi/32
           pause
           e = th_G - th_R + dth
           T1 = -e*C1
           T2 =  e*C1
       else % move forwards if the front has clearance
           e = th_G - th_R + dth
           T1 = -e*C1
           T2 =  e*C1
           if e <= pi/32 % keep the direction otherwise don't go forward this is to keep the vehicle safer
           T1 = T1 + C2
           T2 = T2 + C2
           end
       end
   end
   % This loops until the goal is reached so it will go back to the top
   % and start moving towards the goal
end
% Upon reaching the goal only the rotation matters and it is always the
% same. So the goal orientation get's redefined and the robot starts
% turning using a feedback loop.
th_G = pi/2
while e > pi/180  %% 1 degree equals 1.6cm 
th_R = %ask angular position Robot
e = th_G - th_R
T1 = -e*C1
T2 =  e*C1
end

% We still have some questions for which we need some help. 
% Q how to make the controller C1 for angular positioning
% Q how to make the controller C2 for velocity control
% Q what are the dynamics of the robot and motor. 
% Q is it possible to do these complex loops in an Arduino

The code represents a possible start of a simulated implementation in Matlab. The robot will facilitate an Arduino, hence the algorithm will change form, and it is interesting to already mention some of Arduino statements that could be used. So, instead of all these while loops the Arduino will run several states. A switch within a while loop will choose the state for each iteration. Inside the states certain conditions change the state variable, which the switch will detect. Furthermore, presently a lot of repetitive code is used. Especially for going forward en turning. This will ideally be separate functions that are requested within states. We are planning on making a more comprehensive code in order to make it clearer.

Additions could be:

• A 2D grid map. The sensors could update states of tiles. This way it could update its world map as it drives towards the train. We could use probabilities and let sensor input stack before deciding on the actual observation and switching states of tiles. Also simple search algorithms (A*) could be used to make the robot move more efficiently over the platform.

Interact with the people

There are still some obstacles to overcome. At the moment the solution is way to general. In order to make it more suitable for the train platform case, we would like to make use of the dynamics that govern the people moving on the platform. In order to achieve this one should first make a distinction between static and dynamic objects. Otherwise it is not possible to determine which actions to take. In order to distinct static and dynamic objects, we want to use a coarse 2D grid with tiles of 1 [m^2]. All benches and static static objects are hard coded inside the grid. Then we use the sensors to detect objects. They will give an indication of the tile in which the object is detected. Then it will evaluate the map and decide if it knows the object or not. If it knows the object it can just follow the path that was already planned around the object, otherwise it should find a way to get past the object. In this case it could be a static-dynamic object like a case, which can be moved. Or a dynamic object that can move itself.

We want to find a way to make people move aside, while also going around static-dynamic objects. In order to do this the robot first has to detect the object at 1 meter, the robot will slowly approach the object and use a sound alarm and warning red light in front of the robot to indicate it's movement towards the object. If the range falls below 0.2 meter it will stop and wait, random between 3 and 10 seconds. It is important to build in some random elements in the robots behavior, otherwise it is easy to fool the robot. This approach will hopefully make it possible to cross a flow of people. If the flow is in front of the robot the people have to evade as it moves forward. If the arc in which people evade the robot becomes to big, the flow will probably go around the robot. Also a green light shining on the ground at the back of the robot indicates a positive route for the people in the flow. This could together make it possible for the robot to move towards the train.

Safety is risk. Safety of the surrounding people, but also of the disabled. The green light on the back might not be that useful as disabled - especially elderly - might not be able to move through a mass of people and could follow the robot. The green light might be an indication for people to move behind the robot. The robot should also be safe to bump into for the flow of people.

Closing the gap

As the robot closes the distance to the train door, it will most probably encounter a group of people waiting to enter. It somehow has to make them move aside in order to reach the door. There is also the difference in approach when boarding or leaving the train. Upon boarding the robot could position itself to the side of the train, such that the way is free for leaving passengers. Upon leaving the train the robot could go through the center so the wheelchair can leave the train, before others can board.

As mentioned the train has information about the position of the disabled person in the train. If the disabled scans his OV-card inside the train a beacon starts, but it could also activate a red light on the door that indicates that a disabled will leave the train. The same could be applied as the disabled scans his OV-chipcard at the dock. The robot connects to the beacon at the door of the train, and the established connection will also trigger a red light on the outside of the door. This could make the end phase of the docking less troublesome, because it will hopefully have the effect of deterrence at the train doors where the robot will board.

The new solution

Although it is not quite finished we believe this is due as soon as the arduino and beacons are available, because at the moment we have a hard time to keep it comprehensive and clear for ourselves. That is why we rewrote some of the previous code into language. The different approach of objects is implemented in the code, but the check of the 2D grid is not. Here is the new code: Next week we will start on the arduino and things will become clearer.

%This is a function that finds the goal using position and orientation
while pos ~= goal_pos % We want to loop until we reach the goal position
   % The first loop makes the robot move towards the goal as long as there
   % is no obstacle in it's way
   while S_F == Empty
       th_R = %ask angular position Robot
       th_G = %ask th_goal
       Define angle
       Define error
       Control angle
       if angle_diff <= pi/32
           Forward
           pause 1
       end
   end
   S_G = S_F % the sensor that is looking at the goal is the sensor on front
   % Then the robot turns until the front is clear and drives on until the
   % way towards the goal is clear.
   while S_G ~= empty 
       % update the sensor that looks towards the goal
       Update Goal sensor     
       % while the object is not to close
       t = 0 
       while t < 1
           t = t + 1
       if S_G > 0.2 
           State = Approach{
           sound alarm
           lights on
           Update angle
           Define error angle
           Control angle
           Forward slow
           pause 1
           motors off}
       % Turn until the front of the robot has clearance
       elseif S_F ~= empty
           State = turn{
           Change angle
           pause 1
           Define error angle
           Control angle
           Motors off}
       else % move forwards if the front has clearance
           State = update angle
           Define error angle
           Control angle
           pause random(1-5)
           motors off
           if angle_diff <= pi/32 % keep the direction otherwise don't go forward. this is to keep the vehicle safer
               Forward
               pause 1
               motors off
           end
       end
       end
   end
   % This loops until the goal is reached so it will go back to the top
   % and start moving towards the goal
   motors off
end
% Upon reaching the goal only the rotation matters and it is always the
% same. So the goal orientation get's redefined and the robot starts
% turning using a feedback loop.
th_G = pi/2
while e > pi/180  %% 1 degree equals 1.6cm 
th_R = %ask angular position Robot
Define error angle
Control error
end

Position and Orientation Determination

In the algorithm that enables the robot to find the goal, there are positions and orientation's requested. This section will elaborate on the triangulation of positions and orientations. To triangulate the position there are three beacons required [math]\displaystyle{ (A, B, C) }[/math]. These beacons have positions [math]\displaystyle{ [A, B, C] = [(0,0), (0,B), (C,0) }[/math] in which [math]\displaystyle{ B }[/math] & [math]\displaystyle{ C }[/math] are constant values since the beacons do not move. Next we calculate the distance to all the beacons from the sender/receiver on the robot. We use the timestamp -[math]\displaystyle{ t_{X,i} }[/math]- and the speed of the signal - now assumed to be light speed - [math]\displaystyle{ C }[/math]. The [math]\displaystyle{ i }[/math] refers to the sender receiver node to which the distance applies. In other words the [math]\displaystyle{ i }[/math] refers to the corresponding coordinate system.

[math]\displaystyle{ r_{X,i} = (t_{X,i} \cdot C)^2 }[/math] with [math]\displaystyle{ X \in [A, B, C] }[/math]

These distances and the rule of cosines are used to calculate the x and y position:

[math]\displaystyle{ Y_i = \frac{B^2 + r_{A,i}^2 - r_{B,i}^2}{2B} }[/math]

[math]\displaystyle{ X_i = \frac{C^2 + r_{A,i}^2 - r_{C,i}^2}{2C} }[/math]

The angle is calculated using the two positions on the robot

[math]\displaystyle{ \theta = Atan(\frac{Y_2 - Y_1}{X_2 - Y_1}) }[/math]

One of the main uncertainties up until now is the determination of the distance towards the beacons. That still needs some further research.

Sensors for determining obstacles

For the sensors we did some research on the internet and came up with three possible solutions.

• infrared sensor to detect heat;
• ultrasonic sensors;
• Lasers;
• camera;

For the camera you need sufficient software to distinguish people from other static objects. The infrared sensor would be perfect to distinguish a person from a static object, but this can be inaccurate on warm days or when a person is holding a bag or something cold in front of them. We went to visit Jeroen Houtman with our problem. He told us we could best make use of an ultrasonic sensor, because lasers were to expensive for the scope of this project. While it is hard to distinguish dynamic objects from static objects with ultrasonic sensors, Jeroen suggested that we should make a world map of definite static objects(eg. benches, trash bins, advertisement boards). The ultrasonic sensor can then detect the unpredicted dynamic and static objects. When it detects an unpredicted object, the robot can set an alarm of and tell the object to move away. If it does not move away it is assumed to be a static object and the robot will try to maneuver around it, but instead of moving to the right until the path is free, the robot will turn back after 1 meter and try again to move away the dynamic objects with alarms. Jeroen then addressed us to Ruud van den Bogeart, for the sensors. Ruud van den Bogeart told us it is probably possible to find a suitable sensor for our problem, and that we should come back next week to discuss this.

List of necessities and estimated costs

• 4 Wheels (2 powered 2 swivel wheels) (10,-)
• 2 electromotors (20,-)
• Arduino (70,-)
• Plate as chassis (2,-)
• Beacons (?)
• Sensors (25,-)
• Wires (0)
• Batteries or powerbank (10,-)
• Lights (green & red)
• Alarm (less than 80 dB)

Collaboration process

In this section we will discuss the team process and how the team collaborates. Every week a short update is given on what was done during the week and what was discussed in meetings.

4 September

This day our team was formed. We immediately established each other’s strengths, depending on our background. We discussed some ideas and concluded our main idea would revolve around the train environment. Throughout the week, we communicated who would take on what role in terms of the presentation of 11-9. On Wednesday, part of the group met up again to further refine the main concept. It was then decided we would focus on the boarding of a train by disabled people. Karlijn started working on the presentation, and wrote about the subject, objectives, users and approach. Luka maintained the wiki, while Gijs created an elaborate planning by means of a Gantt chart. Tjacco defined the milestones and deliverables. Throughout the week, a new group member, Jeroen, joined. He started creating the questionnaires we are going to use further in this project. On Sunday, we defined the group roles for the coming few weeks: Luka will maintain the wiki in terms of design process and help with the prototype, Karlijn will do qualitative research on the user requirements by means of the questionnaires and maintain the wiki in terms of collaboration process, Jeroen will do literature research on the state-of-the-art in the field, and Tjacco and Gijs will work on the prototype.

11 September

This day we presented our idea. We received some substantive feedback which we immediately incorporated in the planning: this week we will clearly define the RPC’s, after which we will all create a concept. Moreover, we finish all questionnaires, which enables us to start distributing the questionnaires from Tuesday. On Wednesday we meet again to compare the concepts, and refine our idea. We also received feedback saying we should be clear about the scope of the boarding process we would focus on. Due to that, Gijs started working on a block diagram which would map the entire process from start to finish, to gain clarity. We decided we wanted to focus on every part of the process. Jeroen will in this week start doing literature research, to gain insight in the current situation at the NS. All team members are very involved in the process and all work is divided among the group. Clear deadlines are set and processed in the planning.

18 September

In the section above you can read about the plans that were made for week 2. In the following section, the results of that week will be described we will pinpoint the following steps.

• In week 2 a list of general RPC’s was made; that is, a list that contains the RPC’s that the hypothetical system in real life should adhere to. We decided however that those RPC’s are not applicable to the prototype that we are aiming to build. This week, Luka will define an additional list of RPC’s specific to the prototype.

• On Wednesday, the team met up, and after discussing the concepts we concluded our idea would be largely based on Jeroen’s concept: a lift.

• In addition to the block diagram that Gijs made, the scope of this project will be further defined this week. Moreover, we have picked a specific part of the boarding process that we will focus on, namely, the docking of the robot near the train. This will be further described by Luka. Moreover, Luka will describe the ideal process. Karlijn will describe the process as is.

• Last week, Jeroen has indeed started doing literature research and found out that Canada and France already use the lift system that we have come up with. It does not however autonomously navigate. This Monday, we discussed this in a meeting with the teachers, and came to the conclusion that this is positive: since the lifting part of the system already exists, we can focus on the docking. Moreover, the existing systems can serve as an inspiration and can be a starting point from whereon to start developing our system.

• Karlijn and Tjacco finalized the questionnaires, after which Karlijn started handing out the questionnaires at NS stations. Moreover, questionnaires were distributed via personal networks and Facebook. This has however not yielded as many response as we had hoped for. Because of this, we have decided to extend the deadline one week and we will start collecting all answers and interpreting the data in week 3.

• This week, Gijs and Tjacco will do further research on motion planning, motion tracking and obstacle avoidance.

• This week, Jeroen will focus perform more practical work; besides finishing his literature research he will inform at the Innovation Space what options there are with regard to material and Arduinos and he will update the planning.

• This Monday, when meeting with the teachers, multiple conclusions were drawn with regard to the team. We openly discussed the collaboration to this day. Karlijn, and other team members, missed a leading figure within the group that has an overview of what everybody is doing during the week and if everybody is meeting their deadlines. Therefore, from now on, every week another group member will be that week’s group leader. He or she will check during the week if all is going as planned, and if everybody can finish his or her work before Sunday afternoon. This week Karlijn is group leader. Moreover, we missed clear deadlines last week and a large part of the group only started working on Sunday. This week, the entire group is therefore expected to finish his/her part before Friday. Friday, we will meet to discuss our work and define some final tasks that can be finished in the weekend. This will allow wiki maintainer Luka to upload all sections before Sunday.

22 September

On the 22nd of September we had a group meeting again. We concluded that from that week on, we were going to meet every week on Monday and Friday, rather than Monday and Wednesday. This gives more room to finish all work during the week and gives the possibility to discuss one’s work with one another. Moreover, on Friday we can determine what should be done in the weekend.

We discussed the work everybody had done until that day, mainly Gijs en Tjacco’s work on position determination by using beacons. Moreover, we discussed the materials we think we are going to need and aim to have a list with all needed material next week. Jeroen has checked with 4WBB0 if there are any Arduinos left, which he will hear back from later. Gijs en Tjacco also started coding for the Arduino, which we aim to have checked next Monday in the panel. Jeroen will work on specifying the protoype RPC list with specific measurements and he will elaborate on his patent check. Gijs will summarize all literature he has found so far, while Tjacco will do further research on the beacons. Karlijn will process the questionnaires before Wednesday and re-write the USE part of the wiki and the process description.

29 September

This week, we had a meeting on Monday with the teachers in which we discussed our progress. We received a lot of feedback, which we dealt with this week.

• We have contacted Michiel van Gorp of Engineering Design and can next week pick up an Arduino to use for this project.
• Feedback we got involved the question: what does our prototype show with regard to the problem? We discussed this in the group, and concluded that in the current situation we might not be solving the most important/interesting/challenging part of the problem. We are therefore from now on focusing on the detection in a dynamic environment. This is a problem that is namely not only related to this specific domain of trains, it is a more general problem that pertains to the entire social robot domain. We are focusing on how to create a world model and, especially, how to detect static ánd dynamic objects in the environment and how to differentiate between those two. This week we have already done more research in this area, which yielded several topics:
  • Beacons: by using beacons we can real-time track where the robot is located. Gijs and Tjacco have visited mr. Duarte and from this it became clear we can use the beacons for this project. This means however we have to test the prototype specifically at Duarte.
  • World model: we intend to pre-program static objects in the train environment (e.g. benches). In this way, the robot knows what to avoid.
  • Iemand bijschrijven: Detection of people: blabla (ook iets zeggen over koffers)
  • Iemand bijschrijven: wat gebeurt er als persoon voor robot loopt?
• We also received the following feedback: we should know what the requirements are for an autonomous system in order for it to fully replace humans. We have this week further specified our list of RPC’s, and the results of the questionnaires have yielded additional user requirements.
• From the meeting with the teachers we received the info that at the train station in Den Bosch sensors indicate where the train is going to be when arriving, and where the doors are. This implies that there is an information system at the NS which knows where a train will stop exactly. This may have a slight margin. This is extremely useful for the project, as this means we can assume the robot can access that information system and use that info for where it should go. For the final centimeters, it can use the beacons located in the doors to dock.
• We have discussed with our group what the role of the disabled person should be. We have unanimously decided not to give this person a guiding role in the robot, as we can never assume the skills of the person beforehand. What his role will actually be on the other hand, is specified in the wiki under ‘Idealized solution’.

A short overview of what everybody has done this week:

• Tjacco was group leader, which implies he led the meeting on Friday, and discussed everybody’s progress during the week.
• Iemand bijschrijven: Tjacco, Gijs and Luka met up with Ruud van den Bogaert to discuss the possibilities with regard to sensors.
• Gijs and Tjacco like mentioned also visited mr. Duarte to discuss the use of beacons.
• Karlijn collected all results of the questionnaires and did a thematic analysis on the results, which yielded several user requirements. Moreover, Karlijn updated the collaboration process in the wiki and finalized the process description and user and enterprise analysis.
• Jeroen and Luka both updated the wiki with all the work that was done this week, and incorporated the feedback in the work on the wiki.
• Jeroen has also checked the wiki for consistency.
• Gijs and Tjacco have updated their code for the Arduino.

Sources

Source 1: http://appft.uspto.gov/netacgi/nph-Parser?Sect1=PTO2&Sect2=HITOFF&u=%2Fnetahtml%2FPTO%2Fsearch-adv.html&r=0&f=S&l=50&d=PG01&OS=train+AND+wheelchair&RS=train+AND+wheelchair&PrevList1=Prev.+50+Hits&TD=1328&Srch1=train&Srch2=wheelchair&Conj1=AND&StartNum=&Query=lifting+AND+wheelchair

Source 2: https://www.eurostar.com/rw-en/travel-info/travel-planning/accessibility

Source 3: http://www.germany.travel/en/ms/barrier-free-germany/how-to-book/deutsche-bahn.html

source 4: https://forum.ns.nl/archief-43/bevindingen-proef-station-s-hertogenbosch-873