PRE2015 4 Groep4

Group 4 members

• (Tim) T.P. Peereboom 0783677
• (Marleen) M.J.W. Verhagen 0810317
• (Willeke) J.C. van Liempt 0895980
• (Victor) V.T.T. Lam 0857216
• (Huub) H.W.J. van Rijn 0903068

Introduction

In large hospitals, elderly patients and visitors may have trouble reading or understanding the navigation signs. Therefore they may go to the information desk to request help from human caregivers. A more efficient alternative could be: robots that guide elderly patients/visitors safely to their destination in the hospital. In this way, human caregivers can have their hands free to help elderly with more serious problems that robots cannot solve, like helping elderly stand up when they fell over. Robots can guide elderly easily to their destination, when a map of the hospital is programmed into the robot. Even if the patient doesn't know what to do or where to go to, the robot gives clear instructions for example through touchscreen or speakers.

Scenario

An old man wants to visit his wife in the hospital. Due to the abbreviations of locations and his hunchback, he is having trouble with reading the signage, so he asks for help at the information desk. Here he is directed to a guiding robot. This robot carries a touch screen on eye level which asks the user to press "start". The man presses start and the robot asks him to put on the smart bracelet. This question is also displayed on the screen so people with hearing problems can understand the instructions too. The old man puts on the bracelet and presses "proceed". Now the robot asks where the man wants to go and the robot uses voice-recognition to indentify the user's destination. The robot guides the man trough the hospital to his destination. Because of the smart bracelet the robot can keep track of the distance between the user and the robot. When the distance gets too big, the robot will adjust its speed. When arrived at the destination the robot will ask the user if the desired location is reached. If so, the robot will leave the user. When the user wants to leave the hospital again, he can summon one using his smart bracelet. When a robot is finished with a guiding task, it will check if there are other people trying to summon a robot, otherwise it will go back to its base and recharge.

Users

Primary users

Given that the user space is a hospital environment, a user would like to be treated with care. Therefore we stated a few things as necessary for the user. First of all the robot needs to behave in a friendly way. This means its way of communicating with the user should be as neutral as possible, such that the user feels at ease with the robot. Secondly, the robot should be able to adjust its speed to the needs of the user. For instance, younger people tend to be quicker by foot than elderly. The route calculated should be as safe and passable for the user as possible, with efficiency as second priority such that it does not take longer than necessary to reach the user's goal. Another thing the user needs is a way to communicate to a human if needed, think of situations like the robot being lost together with the user, it needs to be able to tell this to a human operator such that the user can be helped.

Secondary users

Friends and family of the elderly target group can benefit from the use of robots, because they do not have to plan the appointment of the elderly in their own agenda and therefore they do not need to accompany them anymore to their destinations in the hospital. The elderly can go by themselves. Caregivers could also benefit from the use of robots, because now they can better focus on their more important care tasks, instead of simply guiding the elderly to a destination.

Tertiary users

These users should all take into account that they indirectly might work with robots and therefore it requires adjustments for their design, construction, insurance, ethics etc. Industry involved in robot business could benefit financially and scientifically from the use of robots. Although the needs of the primary users are certainly key, the needs of the secondary and tertiary users should be considered as well to ensure high acceptance of the robot.

Requirements

• The robot has to be able to reach each possible destination. Therefore it should be able to open doors and use elevators.
• The robot should be easy to use. It should be easier and quicker figuring out how the robot works then trying to figure out how to get from A to B yourself.
• The robot should be able to calculate the optimal route to the destination.
• It should be clear for the patient that the robot is guiding the patient to the destination.
• It should be easy to follow the robot.
• The robot has to be able to detect if the patient is really following the robot.
• The robot outputs clear visual and audible feedback to the user so the user is well informed about the robot understanding capability and what the user's next action should be.
• The robots are able to track their location in the hospital.
• The guiding robot should have a motor that is strong enough.
• The battery life of the robot should allow it to work several hours continuously.
• The robot has to be able to avoid collisions.
• The patient should feel comfortable near the robot. Interaction with the robot should feel natural.
• The robot should have a low failure rate. It should work most of the time.
• If the robot stops working or in case of emergency, then it should be possible for the patient to contact help.
• Design fitting hospital use, easy to clean, as sterile as possible and low risk of hurting oneself on the robot.

Stakeholders

Stakeholders are those who are involved in the development of the system. The two main stakeholders are the technology developers and the hospitals. The hospital can be separated into different stakeholders: the workers (nurses, doctors and receptionists), visitors, the board of the hospital and the patients. The primary stakeholders are the visitors, workers and developers. Secondary stakeholders are the government, the board and patients. Collaboration between developers, users and workers is needed. The influence of patients that are hospitalised must be considered, they must not experience nuisance with the use of the technology in the hallways.

USE-aspects

Users

The users of the new guiding robot are generally elderly people who have trouble with finding the way in the hospital. Without this robot they would have to ask employees to guide them. Employees may not have time to guide the elderly all the way to the destination. So elderly can still get lost if they don't fully understand the intructions of the employees. They could come too late to an appointment due to this. It is important that the users feel comfortable near the robot. Users may otherwise refuse to let the robot guide them.

Society

Our society is aging so the ratio of elderly and young people is changing. Less young caregivers will be available for the older people who need care. Deploying robots for executing simple tasks reduces the need for caregivers, because they can work more efficiently if they just have to focus on the more complex tasks. The growing demand of caregivers will diminish and the elderly will still get the care they need.

Enterprise

The robot can help patients who have trouble with finding the way to arrive in time. Therefore less patients would arrive too late to an appointiment. This may make the hospital more efficient and could reduce costs. Also industry involved in robot business could benefit financially and scientifically from the use of robots. The robot industry will grow, which creates more jobs for engineers who want to develop and improve this robot.

Tasks and approach (old; Before week3)

In order to test the design and system of the guiding robot, we had two possibilities: use the real robot Amigo or make a simulation. The 3D simulation is chosen, since it would be a more easy suitable way to test than in a real hospital. The simulation will be a first person 3D game where the player will be the test subject. The player is looking through the eyes of an elderly patient or visitor in a hospital.

For making the simulation, the following aspects have to be considered:

1. Unity/Blender The simulationgame will be done in Unity and the 3d models (hospital as environment and character as user) will be made in Blender

2. Catharina hospital map A real hospital map is used for the simulation. The Catharina hospital is prefered since it is close to the TU/e in case tests have to be performed. The 3D environment will be modeled after this map as well

3. Eindhoven Airport robot Literature study and research about the Eindhoven airport will be done to find the flaws of the airport guiding robots, so they can be avoided in the design

4. Interaction The player (user) 'speaks' by inputting a certain sentence and the robot should respond accordingly and correctly through the speakers.

5. Virtual bracelet A 3d model of the bracelet will be made that the character (user) can put on.

6. Same starting point and same destination For now, each simulation will be performed with the same start and end. Later on more starting and destinations may be added.

7. Obstacle avoidance Whenever the robot notices something hinders its way, it should avoid it or move around it.

8. Distance between user and robot (keeping track) Robot constantly checks distance between user and robot (radius). In case distance (radius) is too large, the robot waits or comes to the user. This keeping track of the user can be done with smart bracelets. The robot sends a signal to the bracelet, and the bracelet sends a signal back to the robot. The robot measures the time between sending and receiving and the distance can be calculated by multiplying speed of signal and time.

9. Malfunction/call human In case the robot malfunctions, there should be an alternative for example calling a human caregiver or another well functioning robot.

10. Touchpad and speaker A touchpad and speaker from the robot are used to give instruction to (for example about putting on the bracelet) and have a conversation with the user

11. App for touchpad A program has to be written that allows the user to use the touchpad

12. Survey before/during/after test (feedback) To get feedback about the design and system. A few aspects that can be asked are comfort, ease of use, time-efficiency etc.

13. Elevators in hospital During the guiding the robot has to make use of elevators in case switching between different floors is necessary

14. Navigation system/structure of signage The usual navigation signs of a real hospital will be implemented in the following way. Locations in the hospital where a navigation sign is placed is considered as a node. The hallway that is referred by that sign is considered as a branch. The main entrance is the root and each node is connected to child nodes through branches. The different departments are the so-called 'leafs'. For example, the node 'Main entrance' has a navigation sign that tells the visitor to go to the left hallway (branch) for routes 1-50 and go to the right hallway (branch) for routes 51-100. At the end of these two hallways are again signs (child nodes) that have other hallways (subbranches) connected to it. The sign at the end of the left hallway tells the visitor to go to the left subhallway (subbranch) for routes 1-25 and the right subhallway (subbranch) for routes 26-50. The sign at the end of the right hallway tells the visitor to go to the left or right subhallway (subbranch) for routes 51-74 and 75-100 respectively.

Tasks and approach (new; after week 3)

Smart bracelet

The smart bracelet is worn on the user's wrist. In this way the robot can keep track of the distance radius between the user and the robot. The basic idea of the bracelet is as follows: the robot sends a signal to the smart bracelet and the robot starts the timer. The smart bracelet receives the signal and immediately sends a signal back to the robot. The robot receives the signal and stops the timer. The timer indicates the time interval between the robot sending and receiving the signal. However, this timer is twice as much as the actual travel time. Hence this time has to be divided by 2. The distance radius between the user and robot can be calculated as follows: x=v*t/2, where x is the distance radius between the user and robot, v is the travelling speed of the signal, t is the time between the robot sending and receiving the signal, the factor 1/2 is for correcting the double travelling time.

Literature research has to be performed to find out which electronic components are necessary and which kind of signal we want to use (for example light, (ultra)sound, wifi, infrared, however light and sound are direction dependent and reflect as well).

An example could be the myRIO device that uses wifi as signal and use it in the MATLAB environment. MATLAB starts a timer when sending a signal to the myRIO. The myRIO receives this signal and immediately sends a signal back to MATLAB. MATLAB stops the timer when receiving the signal and the elapsed time between MATLAB sending and receiving the signal is measured. The actual travel time is half of the measured time, since the measured time is twice as large (back and forth).

In order to find out the travelling speed of the signal, reference measurements ('eiken' or 'eikpunten' in dutch) have to be performed as follows: 10 time intervals are measured between the robot sending and receiving the signal with 10 known distances between robot and smart bracelet. The traveling speed v is obtained by v=x/t, where t is half the measured time or x is the double distance. These speeds can be plotted and the average speed can be used for new real future measurements

Robot

A decision has to be made between using real robots (for example the amigo or a robocup robot) or building our own robot with an arduino, motor, battery, wheels, webcam, sensors and platform. We decided to choose for a robocup robot for the following reasons:

• It is more robust than the amigo; it has bumpers
• navigation is already implemented, we need a hospital map
• obstacle avoidance is already implemented, since the robocup robots avoid each other when they play football. We have to define what is an obstacle and what is not.

What still has to be implemented by us are:

• Tracking of the user by using a smart bracelet and calculate time between sending and receiving
• interaction/conversation between robot and user. Robot gives instructions through speaker and touchscreen. In case elderly stops following the robot, because he/she stops walking or walks into another direction, the robot should communicate with the user or information desk, so that a human caregiver can continue guiding the user..

Actions robot should take in case of malfunctions It could happen that the robot has electrical problems, wifi problems and/or mechanical problems, like broken sensor, broken link wifi connection, broken motors. Then the robot should call another robot or call the information desk for human caregivers so that they can continue guiding the user.

Objectives

Objectives of systems

• Guiding elderly patients and visitors of a hospital safely, comfortably and quickly to their destination
• Reducing amount of human caregivers who guide patients and visitors, so they can have their hands free to help patients with more serious problems
• Keeping accompany with lonely elderly, so they can have someone to interact with and have a conversation with
• Keeping track of the user
• Avoid obstacles
• Provide a suitable solution in case the robot malfunctions
• Using touchpad with app and speakers in order to communicate with the user or to give instructions to the user

Objectives of presenation

As presentation of our design, we are going to use a Turtle robot from Tech United. Further information is found in Turtle.

• The Turtle will guide a person from A to B to C etc. on the soccerfield.
• The Turtle will react to the position of the user and the turtle will give signals when he for example wants to makes a turn left.

An app is made for the first interaction with the robot.

App

For the interaction between the user and the robot an app based interface is used. This app will be programmed in Android Studio. When starting on the app, the following things should be discussed: Which features should it hold? How can we make it user friendly? Who are the users?

The design of the app is based on the desing of the Catharinaziekenhuiz website.

interface

Below the interface of the app is described, with all the features it should hold.

---

Homescreen:

• Welkom
  • start button
  • change language (this should be a pop up screen, afterwards you return to the homescreen in the selected language)

---

Next screen

• Ik ben een
  • Patiënt, Bezoeker

---

Patiënt

• ik heb een afspraak
  • Op welke polikliniek heeft u een afspraak? Voor bloedprikken of het inleveren van andere lichaamsvochten, is het niet nodig een afspraak te maken.
    • Menu with all the polis in a scroll menu, the possiblity to type in the poli
• Ik heb geen afspraak*
  • U heeft geen afspraak, maar wel een verwijzing
    • Voor een afspraak op één van onze poliklinieken kunt u bellen naar de betreffende polikliniek of afdeling. Tussen 08.30 en 16.30 uur zijn onze poliklinieken telefonisch bereikbaar.
  • U heeft geen afspraak en ook geen verwijzing
    • Voordat u een afspraak kunt maken op een van de poliklinieken, moet u eerst een verwijzing hebben van uw huisarts. Maak hiervoor eerst een afspraak met uw huisarts.

---

Bezoeker

• op welke afdeling wilt u een bezoek brengen?
  • menu with the sections
    • op welke kamer moet u zijn?
    • Ik weet niet op welke kamer ik moet zijn?
• Ik weet niet op welke afdeling ik moet zijn?
• Visiting times can be checked when the section is know.

---

Ik weet niet waar ik een bezoek wil brengen

• Possibility to fill in the patient
• We should ask if this is possible concerning privacy

Smart bracelet

2 arduino's and two transceivers (transmitter and receiver in 1), 1 for robot, 1 for smart bracelet

robot (continuously) sends signal and starts timer

bracelet receives signal and responds with other signal (continuously)

robot (continuously) receives signal and stops timer

measure time is back and forth, so actual time is half of it

, hence radius distance of user and robot is = v*t/2

if distance is smaller than or equal to required, robot keeps leading

if distance is larger than required, robot slows down (robot follows)

robot has indicator that blinks a few seconds before it turns left or right (turning light)

robot has indicator that turns a few seconds before it brakes (brake-light)

we already have one arduino, so we have to buy another arduino and buy two transceivers

since we want transceivers (transmitter and receiver in 1) that is programmable, we decided for arduinos with compatible transceivers. Arduino options could be: arduino uno, nano, micro. Arduino compatible transceivers could be Nrf2401, Nrf24L01

first we have to talk to Tech United to obtain more information about the football robots. The second Arduino uno and two arduino compatible receiver Nrf2401, Nrf24L01, those three have to be bought, or we may borrow from the LaPlace building, lab room LG0.60 or Flux building floor 0. Both buildings are located on the campus of the University of Technology Eindhoven (TU/e). The used signal between both the receivers is probably WiFi-signal, hence during the operation a WiFi-network link has to be set up and the corresponding network has to be selected and connected to.

http://playground.arduino.cc/InterfacingWithHardware/Nrf2401

https://arduino-info.wikispaces.com/Nrf24L01-2.4GHz-HowTo

http://forum.arduino.cc/index.php?topic=92271.0

http://www.societyofrobots.com/robotforum/index.php?topic=7599.0

Turtle

The simulation of our idea will be made by using a Turtle from Tech United. The Turtle and its programming of Tech United can be used and changed too our idea. With the use of a DEV-notebook we can program and simulate our idea. We tries to make a DEV-notebook of our own notebooks, so we can work at it from home. An alternative would be zipping the .../Turtle2/Motion folder and upload it to Dropbox. When the results are desirable the simulation with the real Turtle can be made. Below a few things we will use that are already programmed are listed:

• The Turtle knows the field and its own position on the field.
• The Turtle sees a black object as an obstacle, which it will avoid.
• The Turtle sees a yellow object as the ball.
• The Turtle is programmed using positions and not using velocity.

We will work in Eclipse on the role_attacker_main.c file.

After saving this c-file in Eclipse, in Matlab a few commands will be executed before the actual simulation can start. In order to start the simulation, the Linux Ubuntu terminal will be opened and the following commands have to be executed:

• sudo su
• sudo matlab
• trc

First we select how many turtles (black triangle) we want to use, in our case 1 (only the guiding robot). And we set the role to 'Attacker_main'. Clicking the 'play'-button will start the simulation and clicking the 'stop'-button terminates the simulation. While the simulation is running, obstacles (black circle) can be added by right-clicking. Using the middle-mouse button will removes the obstacles. Dragging the ball (orange circle), representing the user, can be done by holding the left-mouse button.

How will the simulation look like?

The Turtle knows the field and its position. The goal of the Turtle is to move from a position A via a position B to a position C. During the movement he will avoid obstacles(black). De user(geel) must be guided from A to C.

The Turtle stays within a distance X from the user. When the user is within a range from X to X of the Turtle, the Turtle moves towards its goal.

What if the robot does not follow?

• option 1: The robot moves to fast: he waits until the user reached the robot.
• option 2: The person is stubborn and does not follow

When the Turtle makes a turn it should signal it want to make a turn. We will look if it possible to send a signal when the robot is 1 meters from the turn.

Programming

Everyone will post their progress in this section.

The main programming tasks will be:

• Interaction: what will the robot do/call (through speaker) in case it malfunctions (see section 'Malfunctions')/issue (see section 'Possible issues'). How to implement this?
• Main lead/follow, depending on distance (see section 'Deliverables' and section 'Smart bracelet'). What should the robot do depending on the distance? When robot leads, it follows the preprogrammed path from starting point to destination and may accelerate or keep the same speed (distance between robot and user is small ebough). When robot follows, it goes slows down. Robot calls reception if user is completely off track.
• Track user (calculate distance between user and robot)
• By default obstacle avoidance is already implemented by Tech United
• By default navigation and tracking the robot's own position is already implemented by Tech United. Only the path from starting point to destination has to be programmed.

Since we are with 5 people, 3 persons will be assigned to 1 main programming task (mentioned a few lines back) each about how to implement it in c code. 2 other persons can think about the principles and practice of these main programming tasks.

Which task will be assigned to which person will follow.......

Possible issues

• User walks too slow/robot goes too fast --> robot speeds up

• User is heading the wrong direction --> robot talks, if distance too large --> call reception

• User wants to go to the toilet --> button on robot

• User walks in front of the robot, instead of behind --> robot talks, if distance too large --> call reception

limits --> limit1<limit2<limit3

if x<limit1 --> robot speeds up

if limit1<x<limit2 --> same speed

if limit2<x<limit3 --> robot slows down

if x>limit3 --> robot stops

robot has a velocity not larger than ...

turning light active, 1 second before actual turning

braking light active, 1 second before actual braking

Deliverables

• We show that the user can input their destination via the app.
• We show that the robot can follow a preprogrammed path from the starting point to the destination
• We show that the robot can avoid obstacles
• We show that the robot interact with the user; the robot leads if the distance between robot and user is small enough, the robot follow if the distance between robot and user is too large (see section 'Possible issues')
• We show that robot can indicate when it will turn or brake (see section 'Possible issues')
• We show that the robot can keep track of its own position and the position of the user.
• We show that the robot can guide the user safely and time efficient from a starting point to a destination. Safely is measured in terms of comfort (survey) and robot keeping track of user and interact in appropriate way depending on distance radius between user and robot (see section 'Possible issues'). Time efficiency will be measured in terms of elapsed time and displaced distance (planned route AND unplanned route, for example when the robot has to go after the user because the user didn't follow the robot)

• The users position can be tracked with radius and angle with respect to the robot. This can be done in two ways:

1. Either we use the Kinect 2 only to measure the angle (position of user on frames generated by Kinect 2) and radius (size of user on frames generated by Kinect 2) pf the user with respect to the robot

2. Or we use the smart bracelet to measure the radius between user and robot, use the Kinect 2 to measure the angle of the user with respect to the robot.

Angle and radius in terms of polar coordinates

Option 1 has an advantage of only using 1 device, but a disadvantage is that the Kinect 2 can see multiple persons and the robot is therefore not sure who the user is (may be solved by letting only the user wearing yellow clothes, and obstacles wear black clothes), unlike the case of option 2 (with smart bracelet worn by user)

Option 2 has a disadvantage of using 2 devices, but has an advantage that by using the smart bracelet, worn by the user) the robot can measure the radius of that particular user.

Malfunctions

One of our objectives is to provide a suitable solution in case of malfunctions. The robot’s main objective is to guide a user to its destination, so even in case of any technical defect the user should be able to arrive at the destination. This means that our robot is responsible for the user’s safe arrival. The kinds of malfunctions are divided into mechanical, electrical and wifi connection problems. In case of any defect the user should be able to contact the helpdesk with a telephone attached to the robot

Wifi problems

When the wifi connection the robot may lose track of the users or its own position. If there are still other connections available a robot can switch between channels when the current network channel is broken [1]. It looks for another available connection channel and once found, it tries to connect to it. If a robot detects multiple channels, it has to choose the best one and starts communicating using that channel. If this does not work the robot will try and switch to its backup wifi. The robot could also already have sensed the wifi unit being broken (for example 0 voltage is measured coming through it, which means the antenna is not transmitting any signals), than it will also reroute to the backup wfi unit. So the current robot can continue to guide the elderly safely. An alternative could be employing another robot. In order to extend the lifetime of the network, robots are designed to minimize network communications among sensors as much as possible [2]. For example, it uses an initial configuration with good coverage of the environment. If the signal is lost completely the robot will try to follow its map and last known location to follow the route to get out of off dead, wifi-less, zones. If this fails the robot will after certain amount of time has passed inform the user of its issues and suggest they look for the nearest staff member for further assistance or give the ability to call the front desk via a phone signal. If the loss of wifi connection results in movements in the wrong direction, other solutions should be provided to stop the robot. The developers of the Care-O-Bot solved this problem by implementing a bumper that prevents the robot of being crushed when it bumps into a wall. Also it automatically shuts down when it crosses magnetic band, integrated in the floor. Places where the robot does not need to be (outside the hospital or inside operating rooms) can be marked with this magnetic band. The robot can be turned off manually with emergency buttons too.

Mechanical problems

For a the robot to function properly it needs to be able to move around at a good pace. This is assured by a tachometer that has a light source and a detector (light sensor)[3] [4]. The wheels have slots (holes), through which the light shines. When the wheels spin, the detector can count the numbers of times the light hits the sensor; the light hits the sensor when a hole is aligned with the light source and the sensor and the light doesn't hit the sensor when a hole is not aligned (the light is blocked). In case the robot gives a command to spin the wheels, but the sensor counts 0 speed (either a continuous hit or a continuous blocking of light), the robot knows the motor has issues. When such an issue occurs the robot will stop its attempts to move and inform the user that it is inoperable and has dispatched a request for a backup unit. The robot lists itself as malfunctioning and awaits pickup.

Electrical problems

The robot has to make sure it's battery is charged sufficiently (before it even starts an attempt to guide the user) in order to guide without interruptions. This means for example that at the start of the guiding, the robot should be able to make at least 2 rounds through the hospital. If not, it will go to the charging station to be sufficiently charged. During the guiding, the robot keeps track of the battery level and compares this to the amount of energy it thinks it will need to travel the remaining path. If during the guiding, the robot predicts a battery level that is insufficient to travel the remaining path, it will call upon a replacement and it will return to a charging station.

Screen issues may occur during the guiding. If it shuts down without reason, an alternative could be speech through speakers and speech recognition. When 0 voltage is measured in the screen, even if the robot gave a command to display something, the robot uses this alternative. If the screen displays pixels wrongly, the user can manually reset the screen.

Planning (old; Before week 3)

week 2

• Literature study: Marleen, Willeke
• USE-aspects: Huub, Tim
• Define objectives: Victor

---

week 3

• Create 3 different hospital map: Willeke, Tim
• Describe app interface: Huub
• Create 3 scenarios: Victor
• Describe state-of-the-art guiding robots: Marleen

---

week 4

• Start with Blender: Victor, Marleen
• Start with app: Huub
• What should robot do in case of emergency/malfunction: Willeke
• Rethink requirements
• Describe smart bracelet: Tim

---

week 5

• Finish map in Blender: Victor, Marleen
• Continue app: Huub
• Continue wiki: Willeke, Tim
• Evaluation point

---

week 6

• Finish characters in Blender: Victor, Marleen
• Finish app: Huub
• Continue wiki: Willeke, Tim

---

week 7

• Continue Blender: Victor, Huub, Marleen
• Continue wiki: Willeke, Tim

---

week 8

• Simulation Blender: Victor, Huub
• Start on presentation: Willeke
• Continue wiki: Marleen, Tim

---

week 9

• Buffer

Chef Blender: Victor Chef app: Huub Chef wiki: Marleen Chef presentation: Willeke

App: what does the user see on the touchscreen of the robot Blender: simulation of guiding by robot. Robot keeps track of distance between robot and user and asks questions if distance between user and robot becomes too large.

Planning (new; after week 3)

week 4

• Find the necessary electronics for the smart bracelet: Victor
• Start with creating the app: Marleen, Huub
• Think of what the robot should do in case of emergency or malfunction (Q2): Willeke, Tim
• Finish the pieces about the requirements: ?
• Describe how the smart bracelet works: Victor
• Make an appointment with Tech United: Everyone

---

week 5

• Build the smart bracelet: Victor, Marleen
• Evaluation, do we still miss things?: Everyone
• App: Huub
• Wiki: Willeke, Tim

---

week 6

• Communication link between robot and smart bracelet: Victor, Marleen
• Finish the app: Huub
• Wiki: Willeke, Tim

---

week 7

• Reaction on user behaviour (action) + reaction on user feedback: Victor, Huub, Marleen
• Wiki: Willeke, Tim

---

week 8

• Buffer week 7 + testing: Victor, Huub
• Presentation: Willeke
• Wiki: Marleen, Tim
• Survey: Everyone

---

week 9

• Buffer

Chef smart bracelet: Victor Chef app: Huub Chef wiki: Marleen Chef presentation: Willeke

App: what does the user see on the touchscreen of the robot Smart bracelet: used during guiding user by robot. Robot keeps track of distance between user and robot by using smart bracelet and robot asks questions if distance between user and robot becomes too large. How smart bracelet works: 'Tasks and approack (new; after week 3)'-->'smart bracelet'

Literature

[1] Cassinis, R., Tampalini, F., & Bartolini, P. (2005). Wireless Network Issues for a Roaming Robot. Proc. ECMR’05. [2] Coltin, B., & Veloso, M. (2010, October). Mobile robot task allocation in hybrid wireless sensor networks. In Intelligent Robots and Systems (IROS), 2010 IEEE/RSJ International Conference on (pp. 2932-2937). IEEE. [3] Monica L. Visincy (1999), Fault Detection and Fault Tolerance Methods for Robotics, page 43 [4] Monica L. Visincy (1999), Fault Detection and Fault Tolerance Methods for Robotics, Motor and Sensor Failures, page 23